Search:

Type: Posts; User: EuropeanAM

Page 1 of 20 1 2 3 4

Search: Search took 0.42 seconds.

  1. Thread: Fuel Pump

    by EuropeanAM
    Replies
    2
    Views
    66

    You might contact Rhonda in our Parts Department...

    You might contact Rhonda in our Parts Department next week... she probably has a Part# 30430A8 Check Valve Kit in stock (it has everything needed to rebuild the pump).
  2. Where are you reading voltage (precisely)? ...

    Where are you reading voltage (precisely)? Should be taken AT THE BATTERY, using a DVOM (and cables should be connected largest to smallest, and secured with a stainless NUT or LOCKNUT). NO wing...
  3. Be sure to read the FAQ Section on "Compression...

    Be sure to read the FAQ Section on "Compression Testing".

    Check SPARK, check SPARK PLUGS (IZFR5G, gapped at .033").

    TPS faults need to be addressed- will need to replace the faulty sensors. ...
  4. Replies
    1
    Views
    95

    Cap is not sold separately- recommended repair...

    Cap is not sold separately- recommended repair method is to replace the entire shock-rod kit.

    Where did you get that cap- and what is the part number?
  5. Belt is probably stretched- about the max I would...

    Belt is probably stretched- about the max I would run one on that series is 4 years or 400 hours (whichever came first).

    Put a lbs/in (Inch Pound) torque wrench on the tensioner, set to 70 lbs/in....
  6. :thumb up2:

    :thumb up2:
  7. :thumb up2:

    :thumb up2:
  8. Replies
    6
    Views
    141

    As long as you only emptied the REMOTE tank, you...

    As long as you only emptied the REMOTE tank, you can follow the instructions shown in the FAQ section:

    Bleeding air from the Engine Mounted Oil Tank
  9. That powerhead is now NLA through Mercury.

    That powerhead is now NLA through Mercury.
  10. Replies
    5
    Views
    137

    I would not run this engine again until the...

    I would not run this engine again until the intake has been physically removed as an assembly, and the reeds inspected.
  11. 1021-25 indicates a very low voltage return from...

    1021-25 indicates a very low voltage return from the Shift Actuator's position sensor. There is either a wiring problem, or the actuator has failed.
  12. Replies
    12
    Views
    282

    1. Synonymous in FUNCTION, but "Voltage...

    1. Synonymous in FUNCTION, but "Voltage Regulator" is the correct term (and name of the component).

    2. NO. Under no circumstances should the cranking battery be disconnected from ANY outboard...
  13. Replies
    3
    Views
    170

    Might check the thermostat on the port bank and...

    Might check the thermostat on the port bank and make sure it's coming up to temp properly.
  14. Do you have a MityVac? It is possible to...

    Do you have a MityVac? It is possible to pressure-test the regulator to see what pressure it opens at (using air pressure instead of fuel pressure).
  15. Replies
    6
    Views
    141

    The first bottle is actually the correct oil...

    The first bottle is actually the correct oil (Mercury or Quicksilver Premium PLUS). I would recommend cleaning out the REMOTE (boat) tank and refilling with the Premium PLUS from here on out.
    ...
  16. Replies
    5
    Views
    137

    Did you remove the intake to inspect the reeds? ...

    Did you remove the intake to inspect the reeds?

    WHAT were the actual compression readings?
  17. Replies
    4
    Views
    72

    Should work fine. Make sure that the wire...

    Should work fine.

    Make sure that the wire colors MATCH (black goes to Black w/Orange Stripe). NOTHING connects to the Brown w/white stripe wire.

    Remember that you have to run trim down fully...
  18. +100 Do not even attempt it. What is the...

    +100

    Do not even attempt it.

    What is the reasoning behind wanting to do this?
  19. The tang on the block is a bit further away than...

    The tang on the block is a bit further away than you might think. Look for the wear mark where the spring tang has been contacting... you will need to rotate the spring and tensioner after it's...
  20. Serial Number?

    Serial Number?
  21. The Laser-II probably won't perform well on your...

    The Laser-II probably won't perform well on your setup.

    Note: Props are selected during the RIGGING process (the engine comes with NO propeller).

    As far as it physically installing... it...
  22. 24nm or 18 lbs/ft.

    24nm or 18 lbs/ft.
  23. Replies
    15
    Views
    222

    I would concur.

    I would concur.
  24. Unlikely, but not impossible.

    Unlikely, but not impossible.
  25. Keep in mind that you must supply fuel back into...

    Keep in mind that you must supply fuel back into the system (via the primer bulb) if you're dumping fuel out of the regulator into a separate container.

    Otherwise, the system will be dry in 5-10...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4