Trying to decide what unit(s) to go with at the console.
How much of a difference is there between the Ultra and the UHD? Mainly used for mapping and side imaging.
My budget can handle 1 Ultra...
Type: Posts; User: Kpro1992
Trying to decide what unit(s) to go with at the console.
How much of a difference is there between the Ultra and the UHD? Mainly used for mapping and side imaging.
My budget can handle 1 Ultra...
I believe the just upgraded the oil pump to help fight the #1&2 piston failures. 200 is a detuned 225 and the throttle body will only open up to 3/4 throttle. Change the accelerator cam and have the...
288877
This is what the connectors look like. I gave Garmin a call and the customer service rep that I talked to asked for my address and sent me a new one free of charge. Definitely some of the...
2009 200 VMax Series 2. 450 hours on computer. 50 hours on rebuilt powerhead with Hydrotec Phase 2 kit and ecu upgrade. Considering going to a Sho.
After having problems with my chirp 94sv losing power and not powering on at all, I noticed the female pins on the quick release cradle starting to corrode. Any easy way to clean them up without...
Check out a Super Stick push pole. Fits in your rod locker.
Posted for sale in electronics forum.
I have the nmea 2000 hooked up with to my garmin with the yamaha engine interface cable. It's a 2009 VMax and it will show fuel burn rate. You just have so set the limits on the GPS unit and it will...
When I installed the phase 2 kit in my 3.3 200, I sent the injectors to Rich and he suggested to leave them running a little on the rich side with the higher compression. Went from running 58 in my...
+1 on Skips. He'll make sure your happy.
I have a 2009 VZ200. Blew the #4 piston and had it rebuilt by a local mechanic and added a phase 2 kit from hydrotec. It has ran fine for the last few months but when I got back to the ramp today I...
PART # 99999-03848-00. Thats what I use on my VZ200.
Mark quoted me $550 plus shipping with hub kit
What would be a good prop for a little more speed and good handling? I'd like to stay with a 4 blade unless I can find a 3 that holeshot really well.
Found a throttle linkage problem that wasnt letting me go WOT. Got some updated numbers yesterday with the TRO4.
Running 69.7 at 6k solo
Holeshot was same as original post
water temp 55°
Air...
I had the 761 Blackhawk, loved the way it rode for an aluminum boat but for fishing it was terrible. Storage is at a minimum, and I couldn't find a good way to keep rods out of the way, when the...
Thanks for the tip. Where the throttle cable goes in the motor i found a bracket there with a plastic lock tab. That lock tab came loose and let the cable slide over and bind up. Shifts fine now.
Put my boat in the water the other day and pulled up to the dock, when I shifted into reverse to control the boat it only wanted to make the grinding noise you hear in between gears. Now shifting...
Whatever if you rebuild or swap powerheads make sure you fix what caused it to blow and have the injectors cleaned. Been fighting my HPDI for a couple months now.
59-61
Not sure if it helps but this is how they are mounted on my 191 Cayman
*Can't get the picture to upload
Thanks I'll try to get my hands on one to test.
3.3 with hydrotec phase 2 and 225 ecu
Is the Bravo that much easier to turn? I'd like to get my WOT rpms up to 6000.
I have a Ranger 191 Cayman flats boat. 200 HPDI with Phase 2 and ecu upgrade currently running a 24 pitch TRO4. Holeshot is about 4-5 seconds with breakover around 4500 rpms. When I'm fully loaded...