Contact Golden Channels they will fix you up. They were a tremendous help when I rigged mine.
Type: Posts; User: yogib
Contact Golden Channels they will fix you up. They were a tremendous help when I rigged mine.
I'd put my money on the glide with the amount that will be chunked at them this weekend. Especially since Milliken just released his big baits video from Ozarks.
NMEA will show engine data including hours on your Garmin provided you have the proper connections. I suggest contacting Goldenchannels.com, they are everything NMEA and were very helpful when I set...
How old is the Metanium? Thanks.
Yes, there's a cable that connects to the motor under the cowling. On my 2023 200 SHO it was a PITA to run through the grommet. I recommend giving Goldenchannels.com a call, they specialize in NMEA...
I've been using one (Ionic 125ah) for a month, zero issues so far. I'm running everything including livescope and 2 12" graphs never seen it below 85%.
Thanks for the information. What are the pros/cons of the raker vs Bravo style blades?
Does anyone know what the Razor vs Razor XL difference is, I assume diameter? I could not find any specs online. Thanks.
They will answer email it just takes a few days. I just got an email from him Sunday.
Should I load this more towards the bow, middle, or stern? I did notice the boat wants to list or tilt fairly hard at times to the right mostly at lower speeds but it's not all the time and I've...
Sorry for the delay in posting the setup I've been busy. PTP is 3/8" at max JP height, and roughly 2.5" middle setting, 4.75" lowest setting. I measured this using a level off of the pad, leveling...
It was a 5 on my expride just FYI
No I don't attempt to drive through or with the chine walk, I trim down immediately. However even at this trimmed down level it takes alot of effort on the wheel to turn left, you can just tell...
I'm having chine walk issues with my current setup (Falcon F195). Above 65mph and high trim its starts to walk and gets out of control. I'm running a 24p razor 4XL and I'm getting 5800 max at full...
I'm having chine walk issues with my current setup (Falcon F195). Above 65mph and high trim its starts to walk and gets out of control. I'm running a 24p razor 4XL and I'm getting 5800 max at full...
I'm having chine walk issues with my current setup (Falcon F195). Above 65mph and high trim its starts to walk and gets out of control. I'm running a 24p razor 4XL and I'm getting 5800 max at full...
Having issues with my F195 chine walking above 65 mph or so. I've tried jackplate settings from 1 to 20, defnitely runs better higher 15+ but still starts walking and gets uncontrollable. I've...
I pulled a guide completely out of the wrapping on my 7'2" Expride MH casting rod. I lost the last guide before the tip, does anyone know the size. I was thinking around a 5?
There was no additonal tubing to adjust. Also it looked like the fuel was connected using an otiker style crimp ring, maybe they changed recently?
Used a TH Marine troll tamer, worked well. I used the stock collar to keep it attached to the grommet. In hindsight I should've left the hard tubing a little longer coming out of the splashwell as...
I've definently done it on the tokyo rig and it works well. I might try it tomorrow, it also may add some sound to the presentation for better or worse.
I agree the hose clamp will hold better but I think the main problem is the angle of the tube/grommet.
I'm having an issue on my rigging grommet. The angle is such that it pulls the retainer sleeve off of the rubber grommet that is attached to the outboard when the motor is turned right (boat turning...
Has anyone tried using 2 weights stacked for punching? I ran out of 1.25oz weights and was considering trying a couple of 1/2 or 3/4 stacked.
I'm having an issue on my 195 rigging grommet. The angle is such that it pulls the retainer sleeve off of the rubber grommet that is attached to the outboard when the motor is turned right (boat...