Search:

hours are 512.
Injectors were flowed, cleaned and tested a couple of years ago by previous owner after a compressor failure. Not saying they do not need it again, there was some junk in the fuel...

Okay, I appreciate everyones assistance. This motor does have aftermarket refurb coils. I have seen and heard some stories about them causing a miss at idle but seem to run fine on step. I bit the...

IF gel coat is thin then yes, likely need to be resprayed. Looks like sun damage to me. I would talk to a shop though. It may cost more to repair than to replace. I recieved a quote from ranger a...

Well i am glad i bought the pin gauge set! Just finished adjusting the throttle plate gap and roller. I was way off with my assumption, the gap measured .086. Now i understand this is likely caused...

Thank you! The adjustment is way off then. Ill check it with the gauge when I get home. IT is bizare, the blue locking paint is still there from factory. If it was something wearing then you would...

Thank you!

At the 12 o clock position, on the side facing the flywheel, between the throttle plate and throttle body.

I ordered pin gauges which were supposed to be delivered yesterday. Says they’ll be...

1B347098
2006 Mercury Proxs 225

Waiting for my service manual to be delivered. Does anyone have the air gap handy for this engine? Mine appears to be in the 1/32-1/16 range. Seems large from my...

2006 Proxs 225 1B347098

Seeing some conflicting information on the web, I gapped the new IZFR6J plugs to .032-.033 per Dons Sticky. Then being told by a local tech they should be .040. Then...

Got the new crossover on order from European marine, overnighted. Great service!

Will now need to get the idle figred out.

2006 & prior ProXS: .032-.033", this is from the sticky at the top of the page. That is no longer accurate?

Thank you, I’ll get one on order tomorrow.

so the issue I’ve been having with this motor is a misfire when idling and just above idle. I just recently bought this boat, but i do know it has had...

1B347098
2006
225PRO XS

Been dealing with some issues on this motor. Just found a pretty bad fuel leak coming from bottom fuel rail cross over. I picked up some brown orings from an auto parts...

That is what I did with this particular connection. The down side is, the whole trailer appears to be the same way. Was just surprised to see this "quality" on a Ranger trailer.

Good morning, I recently purchased a 2006 Ranger z-20. The back up lights were not working, I started to troubleshoot and found one light to have low voltage (fluctuated between 0-5vdc). When...

Today i spent the better part of the day siphoning 27 gallons of fuel. Purged the fuel tank with a mixture of heat and sea foam, sloshed it around and siphoned that out with a compressed air vacuum...

1997 mercury 200 HP EFI
SN OG570907

Let me start by saying this motor has been nothing but flawless. My boat sat for about a month and a half in the garage without use. Took it to the lake...

SCOTT196, That is one thing I am unsure of. My plan is to hook up a secondary digital tach to verify the dash gauge.

STLBassBuster, To my knowledge the prop has never been worked, I bought it...

You may be correct, currently running a 3 blade. What is crazy is, this boat had a 23 tempest on it when I purchased. I could only run 1/2 throttle with it. I have no clue how to guy ran it that way....

Hello all,

My 97 202 Elite has a 97 Merc 200 EFI. I just installed this passed weekend a manual 6" jack plate with prop shaft set 3.5" below pad and a 25P Tempest plus prop, full gear in bow...

I called, Hull ID number should be all you need. To be honest the girl seemed pretty frustrated to have to send it out. She had even said they need to start charging for them (which IMO is...

For those interested, here is what an original mountain home build sheet looks like. 514455

The sad part of seeing this is, my boat currently has a 200 EFI on it. :sweating:Not sure when the...

I'd guess 12k - 14k. Being spring is coming, probably will get a little on the higher end. However, it does appear the used boat market is cooling from what it was a year ago.

You sir, hit the nail on the head. I spoke with Deans, they were kind enough to send me the original build sheet for my boat. Primary color is MIDNIGHT BURGUNDY.

Good morning, I am trying to find the color match for my boat. I believe I have it narrowed down on GLS website. Just curious if anyone knew off hand. It is a redish maroon color. The closest craft...