thank guys, I never considered the cone angle. bob
Type: Posts; User: bobimo
thank guys, I never considered the cone angle. bob
have mega live hook to helix 9 mega si g3n. In the down mode i can seen a 1/16 oz crappie jig at 25 feet, sensitivity at 10 contrast at 10, when i switch to forward mode and click transducer up 6...
has anyone mounted a mega 360 on a old minn kota 1o1 trolling motor
bob
Have 1999 518 ranger with mercury efi 200hp and running a 25 tempest plus prop. will adding a jackplate make this boat ride better in rough water.
bob
repaired lower unit, ran boat for about 30 minutes no problems prop did not change color
bob
found water in lower unit, waiting on parts, will update when motor is ok to run
bob
nothing new on boat, boat is a ranger 518, I cleaned prop and going to run it to see if the prop changes color again.
all ground strap good, checked conunity between prop and ground on starting battery less than .5 ohms, boat is only in the water when it is in use, same lower unit same prop and washers for 14 years....
prop is 25 tempest plus, what and where is the continuity washer, i have run this prop for 14 years in the same water with no problems
bob
it is the whole prop and i did not seen this problem until the water started to cool off, less than 60 degrees.
bob
1999 200 hp efi mercury s/n0g866278, put a new power head onlast year and while trying to get it to run had a fuel problem, it was dumping fuel out the exhaust, noticed the prop ( stainless) had...
I have a 1999 518 ranger setting on a 1996 496 ranger trailer, trying to find the specs for a 1999 518 trailer so I can adjust the runners to fit my boat or anyone know where I get a trailer that...
I ordered a as ce qde cable it will not connect to my mega live transducer. the mega live transducer cable has a female end and the
as ec qde also has a female end and will not connect. can I use...
I bought a used mega live , it came with a ethernet cable, I am trying to connect the mega live directly to the helix 9
I tried using the ethernet cable, when I put the mega live in the water, it...
it was the lower seal on the crankshaft that was not installed correctly, replace seal and no leaks
2000 yamaha 200 hpdi motor leaking engine oil out of the lower unit weep hole, checked under cowling did not see any oil leaks, checked and replaced lower unit oil, no water in the oil, any...
have went through the setup for transducer selection and installiation, it will show the gt8 but will not read when boat is on plane, lose sonar signal as soon as the boat starts to breakover. the 9...
have 2 new 10 inch units on bow and one older 9 inch unit on console all net worked together.
installed a gt8 in hull transducer to read when on plane, 9 inch unit will not recoginze transducter,...
thanks, will recheck wot timing using starter.
bob
1999 mercury s/n og866278 200hp efi. how do you set the max timing on this motor. can it be done without running in the water at 5000 rpm. I now have the timing set at 4 degree at idle with motor...
thanks, you were right, I did not have the throttle at wot. set timing at 4 degrees atdc and wot at 16 degrees btdc will setup on water later.
thanks bob
1999 2oohp efi s/n og8866278
my service manual says to set the max timing while cranking the motor with the starter. disconnected the bias, disconnected the ecu, removed all of the plug except...
1999 mercury 200hp efi s/n 0g8866278 just put a rebuilt powerhead on. Do I need to change the reeds.? The one in the engine is the original ones. Would boyesen reeds help the performance.
bob
got lucky, took the front of the manifold off to see if any of the fuel injectors where leaking. found the bolt that hold the fuel rail loose, one was ready to fall out, tighten the bolts and...
I have a 1999 mercury 200 hp efi s/n og8866278. How long should the fuel system hold pressure, the fuel pressure starts at 38psi and within and hour drop to 25psi this is with the motor not...