Just for notice, they reported they drained the lower unit oil prior to the pressure test. Not sure if they did any soapy water around anything. We didn't discuss that. Thanks again.
Type: Posts; User: BigBucketMouth33
Just for notice, they reported they drained the lower unit oil prior to the pressure test. Not sure if they did any soapy water around anything. We didn't discuss that. Thanks again.
First off, thanks for the input. Don, that is funny you should say that. I wondered myself why so much pressure? To me, even 3-4psi would reveal any leaking components when properly checking...
Wouldn't you see a pressure drop during pressure test if that were leaking? According to tech at dealer, he went ahead and replaced the seals around the while pump when he had it down. Crazy little...
Serial# 2B590145
4 Stroke Pro XS 250 sometimes leaks lower unit oil from water intake.
I changed the water pump awhile back and when the motor was trimmed up lower unit oil trickled from water...
I run a megaware keel guard on my 721. Put it right below bottom wing and its been there for 2+ years with no issues at all. Have beached on cement ramps, sand, and in mud. Installed myself per...
Was unaware of Vessel View mobile not reading historical codes. If the alarm is stored in the ECU why would it not show up on VVM?
I did happen to pass thru some hydrilla at one point coming out of a cove, but for the most part all clean water. I'm not going to rule out come grass could have been picked up. I just pulled the...
Appreciate the info. Will have the alarm properly read to determine the issue. I have MPP until July 2024 if I remember correctly. Thanks for the help and I hope it isn't anything major. Hopefully,...
Serial # 2B590145
This weekend at the lake I encountered an alarm that I have never had. My boat ran fabulous, no problems at all. I hit top end RPMs, normal water pressure, and everything was...
Just received a new bow shroud from Phoenix and plan to install it soon. Has anyone replaced theirs recently? If so, which route did you take? I know it will be basically impossible to drill holes in...
Thanks, fellas. I am going to troubleshoot and pull it tomorrow.
Assuming the relay harness for atlas jackplate is mounted under the back deck by the transom on the starboard side? My jackplate quit goin up this weekend and Im assuming relay or switch without any...
UPDATE:
After extensive troubleshooting yesterday I found the culprit. A faulty rocker switch caused extensive voltage drop to the 360. I was getting 12.7 volts at switch, but leaving the switch i...
Thanks, Data for reply. That's the problem I am encountering. My sonar tab is not displaying any transducers to choose. I just downloaded the new software to SD card. Will install on unit shortly and...
Recently, I received my 360. Wired it up with a Y cable so I could utilize my MEGA DI on trolling motor if need be. With everything hooked up, my Helix 12 will not even power up. I simply unhooked...
Thanks for the help. Yes, I agree. Seems like tasks that are thought to be simple, always turn into a "BIG" job lol.
I thought I saw a post on here awhile back about the cord replacement for the boat trailers. Mine is getting a good bit of wear and I would like to replace it. Anyone have a link to the cable that...
Good info. I figured it would be way better, but just wanted to hear some feedback. Thanks
I just ordered a mega 360 and was curious how many of ya'll are running a switch for the transducer? I read somewhere that humminbird recommends adding a switch during the install. I have the switch...
I just bought one last night 10/27 from Bass Pro as well. The day before that I checked and they were "out of stock"
Just curious to know why it randomly tried to detect it when all this time it has been reading perfectly fine from the XTM MDI trandsducer on my trolling motor. Are there any particular reasons as to...
Yesterday while on the lake my graph went stupid. I bought and installed a couple months ago. Everything has been great with it until yesterday it started acting like it was reading from a Mega 360....
Thanks for the help. I actually was able to lay under the trailer and verified that XP100W0301 is printed on it. I never noticed it before. Thanks for the help and info. Now, I will begin looking for...
I installed a KeelShield as per the instructions that came with it and I am highly satisfied with it. Over 2 years on the install and all is well. I put my below the 3rd bow wing and it works as...
Does anyone have a lead on the model Fulton jack on the trailer for a 2019 721. Obviously, its a marine master trailer and I have a fulton jack on it. I need to replace jack and want to make sure I...