It does both, holeshot in keeping the nose down when the motor is trimmed in and helps get the nose up at lower speeds and keeps it up at lower speeds while it is still in the water. Reduces...
Type: Posts; User: KevinH-BCB
It does both, holeshot in keeping the nose down when the motor is trimmed in and helps get the nose up at lower speeds and keeps it up at lower speeds while it is still in the water. Reduces...
546644This is what I am looking for. This is NOT my Rig
Hydrofoil Needed
I have a light 20'-5" bass boat, '86 Shadow tunnel boat. I have a '93 Merc 200 2.5L on it with a bass mid, and Bob's Machine low water pickup mounted to a 10" manual jack plate. I mounted a Garmin...
Thanks! That is the detailed information that I was looking for
The part is over $300 for an injection molded part. That is robbery!
What does it do? My buddy’s 3L (2016 200Pro XS), doesn’t have that chamber.
I have a 2016 Merc 250 Pro XS. The rear section of its plastic handler was broken. The 'ear' that holds the smaller of the two grommets is broken. The larger grommet goes over what looks like a...
I just got mine from Jacos Marine - great quick service! I paid $529 NIB with hub and with shipping for the 26P Fury 4. Remember to purchase the shaft grease (I forgot).
Troy - where is this installed?
There is no good place to put a choke on the outside of the trolling motor, but you got me thinking that I may be able to sneak one or two inside the head cover. I'll pull the cover and see - thanks...
Larry - I did try the ground between the starter and TM batteries - no luck. Bass Cat Boats stated that they have found that this created a lot of issues with their rigs and strongly advised against...
Latest Update: I took the rig out yesterday. I disconnected the on board battery charger before I hit the lake. This did not make a difference in my case. I'm stuck at this point of anything else...
Try Jacos Marine, jacosmarine.com
Based on what you are saying then, the quad, dual, and wide angle beams are all out of the same transducer, the one bonded to the inside bottom of the boat.
I guess since I also have a Garmin 93SV...
I have an in-dash HB 788 HD. It has two transducers, a pencil size transducer on the transom, and what looks like a trolling motor transducer bonded inside the hull at the back of the boat. I have...
I have run a temporary ground wire with a in line fuse from the trolling batteries and the starter battery. It did not help me in my case. I will try disconnecting the charger to the starter...
Justin - glad to hear that you are having some success. I am like you, with the MG Digital Tour. I checked to see if there was any resistance between the starter battery and the trolling batteries,...
Parker - Be sure to let me know how you make out with the MK experiment. I've always had MK's. I have a MG on this new rig BC it came pre-rigged and I got a good deal. The foot pedal steering...
Sat. Update
I still have interference even with the dedicated PWR run, shielded cable, coiled cable - twisted and folded on itself, ferrite magnets on both transducer and power leads to Garmin...
No - Justin, as far as my issues, it's only with traditional Sonar in both Chirp and 200 MHz. I do not have interference in DownVU or SideVU.
TreeGuyUs - I have the GT52 Transducer on both units....
Appreciate that - Donnie! I had not thought of that. Good reason to post :-) Get other people's ideas and hear what has worked for them! I'll let you know.
No - when I remove the transducer from the TM I do not get interference. Even with the transducer mounted to the TM I do not get interference. My problem with interference starts when I stow the...
This is what I tried last night:
I pulled the access wire out of the boat and laid it on top of the deck doubled - WRONG! Worse.
I coiled it up and I tight coil and zip tied it so that it would...
I definitely disagree from my personal experience, and two other Authorized repair centers recommended this to me. It's definitely worth a try, since it gain for most for my situation so far.
Guys, I think the next steps are as follows for me - more experiments:
I am going to remove the excess transducer wire from inside the boat. I am thinking that when I insert the excess wire...
Parker - I would. This one change has gained me the most. At least after I had the internal ground installed on mine, though I still get interference, I get a clear enough picture to see what is...
