Search:

Thanks for the input guys! I was hoping to just run it trimmed down vertically. I have almost exactly 10” of clearance’s from my skeg to the pavement.

I have inherited a 1990 lund. It didn’t come with a transom saver setup. My 40 hp Evinrude can trim all of the way down with plenty of ground clearance while traveling. My question is do i really...

I will definitely try the adhesive! Thank you!

Thanks for the heads up!!

The black gasket (trim) piece that covers the opening edge of the livewell has been trying to come loose since last season. It makes the livewell divider a real pain to remove as I have to hold the...

Just needing some clarification on these G2's. Does the Evinrude G2 in the OP pic eliminate the hydraulic hoses for steering (helm to the outboard)? I know that the G2's have some sort of built in...

I am running a 21p tempest on a 115 pro xs ct. im getting 6150-6200 rpm at 47-48 mph. Are the advertising videos for turning point really telling the truth? Would an express mach 3 perform any...

Thanks for the replies fellas. ��

Is a young Marine new on station required to notify his/her COC before tying the knot? Then is further required to take a 7-8 month course about getting married? I don’t remember it being like that...

I have been looking into upgrading from my Maxxum to an Ultrex but i cant seem to wrap my head around having to spend $2000+ and then having to address vibration issues.

It has been a while since ive logged on so I apologize if this has been discussed. I just noticed that the Ranger website shows dual power poles on the 198p 😮. Does this mean my 188 can handle dual...

Yes sure enough there is a black block under the console that is labeled livewell timer :doh:. Unfortunately there is no adjustment on it. I may unscrew it later and see if there is something on...

Hello,

I am looking for a bit of insight on a couple things. I have recirc, auto, and empty. Auto mode is what i keep my selector set on when fishing. I recently have been able to hear...

Thank You for the clarification. I was thinking it should be connected to a straight 12v source on the auto side. I will try the button, and also fill the bilge up to see if it kicks on.

Ok this may be a stupid question but I am confused. I have a 2017 RT188 and it has the Rule Mate 750 auto bilge (3 wire) installed from factory. The switch on the console is just a basic on off,...

I noticed the other day that my console will wobble if you lift up on the steering wheel. The wobble was enough to alarm me. The console itself isn’t the culprit, but the aluminum decking that the...

Has anyone tried to order a cover for the recessed foot pedal on a Ranger RT188? I was wanting to install an Xi5 and thought about covering up the recess. I thought ive seen a picture on here of an...

I just mounted a transducer plate with 5200 fast cure and it has held up very nicely

Gshellems has a good thread on the install and gives links to the struts and mounts. Here is the link to the thread http://www.bbcboards.net/showthread.php?t=779482....If the link doesn’t work then...

Hds 7...It does look close in the pic but i have plenty of clearance for my hands to be on the wheel. Not sure if it would work without the hydraulic system. I believe the wheel sets closer to the...

I'm running a 21p tempest on my RT 188. Getting 6100-6200 rpm at 49 mph on gps.

I did coat it in a nice layer of Thompsons Water Seal :thumb up2:

I just used three self tapping screws and secured it to the aluminum support piece that runs along the length of the lid.

Hinge is a 12 inch

Yes i added gas struts to both front storage compartments. It was a pretty essy install. I feel that as much as these rigs cost, the struts should be included from factory.