Thanks Wayne P. I knew you would get it clear. I researched for over an hour last night before posting. I also played around with the settings this morning. There is an option for transducer that...
Type: Posts; User: Gman24
Thanks Wayne P. I knew you would get it clear. I researched for over an hour last night before posting. I also played around with the settings this morning. There is an option for transducer that...
Helix 10 CHIRP SI GPS G2N
It matches the display on the SYSTEM STATUS view
He had never done an update on the unit. it was version 1.35 i believe. The HB software update said the unit was ready...
In the process of purchasing a Helix 10 G2N Chirp SI DI Combo from my buddy. The Unit was an extra that came off his boat before trade in. He had used it for 2d imaging at the bow and used the built...
Thanks Jethro1. I justspoke with a Yamaha Mechanic. He said exactly what you just said. The o ring slides inside of a cylinder that the pump male end slides into forming the seal to prevent pressure...
Yes that's the diagram that I found.i'm wondering if my o ring has expanded. It will not lay on top of the tube. It actually slides completely around the tube part. That's why I said it seems to not...
Can someone tell me where the small black o ring at top of the VST tank pump goes. Does it just slip over the male end tube at the top of the pump. To me it appears as though it serves no purpose...
Thanks Rich Z. I talked to a mechanic yesterday. It is called a TRIM LIMIT SWITCH. I was told most Yamaha motors don't have them but he had ran across a few that do. I don't think mine does. He...
Just talked to the mechanic. XI9INDY, you are partly correct. I was told that most Yamaha engines DO NOT come with the , it's called a TRIM LIMIT SWITCH. He said if mine does it would be located in...
Looking for possible short in Trim switches. Still don't seen how this could cause a rpm loss. If anyone has possible cause or solution would be very helpful.
You may be correct. The switch I was referring to is the trim position sensor. However, there has to be something that keeps you from trimming the motor completely out of the water when at WOT. My...
There is one on my Yamaha HPDI.
There is a trim Stop switch on most motors that WILL NOT allow the motor to be trimmed past a certain point at WOT. It bypasses the trim button when tripped. It will be located just above the trim...
Possibly throttle interupt switch. Thats what tells your engine to kick into all cylinders when not at idle.
Yamaha 2006 200 HP HPDI has intermittent rpm stutter when accelerating. I have replaced every filter along the fuel line including mystery filters. Engine runs fine from Idle to full throttle. Only...
If your boat has the c channel rub rail like my Zx200 you can do your install like mine. I have a post in the Boat and Trailor Bling board. Look for Nav light rub rail install and UV light rubrail...
Thanks. I got them from 10 OcLED (Tennessee Led). You could use Bluewater strips as well. You can do a google search. The Nav Lights (Red and Green) 4 -48" UV Strips and 2- 18 inch Green Strips...
Here is a link as to how I did mine. I did the bow lights as well as the UV black light and a moon glow strip in the center of the boat. I got the idea from the Nightfishion system. I just didn't...
Good luck finding anyone with ANY Ultrex in stock right now. Beware,there are some sights out there who claim to have some in stock just to get you to order from them. I went through this last...
You are correct. I'll take my chances. There were pieces of fishing line as well as plastic pieces of crud ( from used plastic baits i would bet) that came out the end of the cable. I'm assumimg...
Recently my throttle cable had become stiff and was sticking slightly at times. My last trip it became so stiff that my hot foot bolt came loose on my side (was a rusty screw, which was another fix)....
Usually the bigger pumps have higher amp pull. If your fuses aren't rated for that amp draw it will blow the fuse or trip the breaker whichever you have. I have read where some have upgraded to...
Just put a Sams Club group 31 AGM on my 06 200 HPDI. Been running strong for a out 3 months. I went with the bigger size 31 to handle electronics load. The reserve capacity is what you want to look...
Just put a gallon of XLF in my tank tonight. Been using either the XLF or Premium Plus for several years in my HPDI.
Great info! Thanks for the response.
I am in the process of ordering mystery filters and all filters related to my 200 HP Vmax Hpdi. I have always thought my motor was considered a 2006 model. However I was looking up the serial...