Search:

Type: Posts; User: Joe from Virginia

Search: Search took 0.00 seconds.

  1. You may need to check to make sure you have clean...

    You may need to check to make sure you have clean power going to the unit. Is your power connected directly to the battery, are you getting interference from another source. Your setting on the...
  2. Anyone Mount a Hummingbird 360 to a Minkota edge trolling motor

    As stated above I have an Edge trolling motor. I looked up the requirements/compatibility with trolling motors and the Edge was not listed. The only reason I can think that it wont work is due to the...
  3. Does Anyone Sell a Spider Grub in a Clam Shell

    I have tried these grubs with some success but when purchased many are bent out of shape and not usable. I have tried to correct this problem with boiling water like i do larger baits like a fluke,...
  4. Ranger RT188 Center Console at Cabelas

    Has anyone bought/tried the center console being sold by Cabelas?? Looks nice, just wondering if it will look ok. I am concerned that it has a weight limit around 250 I thing.
  5. Replies
    1
    Views
    348

    Ranger RT188 Trailer Fender

    This past Saturday someone hit my trailer and crushed the left/starboard side fender on my 2019 trailer. This is an ezloader and wondering if anyone knows where I can purchase a new or used fender...
  6. Thanks for the response to all. I have ordered a...

    Thanks for the response to all. I have ordered a single battery power switch that I will run everything through except trolling moter.
  7. Electrical Question for 2019 RT188

    I have on and off power switches in the back of the boat in the battery compartment. One is dedicated to the trolling motor batteries and the other controls the console power. After a couple of weeks...
  8. Replies
    2
    Views
    279

    How to remove Hull Numbers

    Ok all, I am the proud new owner of a new/used 2019 Ranger RT188. The boat is metallic charcoal or something like that. Anyway, the trim on the side of the boat is red. The old Hull Numbers are also...
  9. I am sorry. I meant to ask about mounting the...

    I am sorry. I meant to ask about mounting the 3in1 transducer to the trolling motor. I think Kennybryan understood that but not sure. Old age is hell on the mind.

    Joe from Virginia
  10. Transducer mount for 3in1 side scan

    I have been checking the web for a transducer mount for my lowrance TI2 3in1 transducer. Found one made in Canada that is expensive and another that reviewers say is a bad product. What are u using...
  11. Ok, thanks all. Got the information and have...

    Ok, thanks all. Got the information and have purchased a tire and wheel for tomorrows trip. Hopefully everything goes well and I will be a new Ranger 188 owner. Now to sell my other two boats.
    ...
  12. Yep, it is a Ranger 188, got confused because I...

    Yep, it is a Ranger 188, got confused because I was also looking at a Triton TX last week. Anyway, I have gotten the info I needed and have purchased a wheel and tire for my trip tomorrow.

    Joe...
  13. Thanks everyone. Like I said in my post I am...

    Thanks everyone. Like I said in my post I am picking up the boat tomorrow and dont have time to order, I need it now. I will be driving about 200 miles back home with the boat and scared to tow...
  14. 2019 Ranger RT188 Trailer Tire Help

    I am buying a RT 188 tomorrow and the owner says the boat does not have a spare tire. Could someone please tell me the tire and wheel size to include how many lugs and spread 4.5 I think.

    Joe from...
  15. I am sorry. I also need to know how many lugs and...

    I am sorry. I also need to know how many lugs and size. I think the wheel is a 13 inch with a 4.5 pattern but need to know for sure before I run out and buy today.

    Joe from Virginia
  16. Tire and Wheel size on 2019 Ranger TX 18 Help

    I am buying a used boat tomorrow and the owner now says he does not have a spare tire. I have to pull the boat a couple of hundred miles home and would want a spare tire and wheel while traveling. I...
  17. Replies
    42
    Views
    4,199

    Any update on ramp repair as of 7/31/2020? Have a...

    Any update on ramp repair as of 7/31/2020? Have a tournament coming up in August and wondering if their is enough tie offs for 15/20 boats after being dropped in the water and awaiting partners,...
  18. Replies
    3
    Views
    377

    Fish Culling Clips

    Anyone know where you can buy the culling clip attachment that works like a cloths pin. I don't want to buy the whole system, I have Cull Rights now but they have the metal rig where you have to...
  19. Replies
    6
    Views
    523

    I have a deka group 24, 1000amp now. Like...

    I have a deka group 24, 1000amp now. Like 250bassFL said, after tournament I would just hook a charger to it and top it off. The charger did not indicate state of charge required, just a light would...
  20. Replies
    6
    Views
    523

    Bill, follow what you are saying and appreciate...

    Bill, follow what you are saying and appreciate your response. All these years of fishing and never really new what the state of charge was at the end of day on the starter battery. Started checking...
  21. Replies
    6
    Views
    523

    Starter Battery Question

    I have a new deka starter battery on my 200hp Merc, 1996. At the end of a tournament day my starter battery is registering 77 percent charge remaining. Is this normal? I am running two depth finders,...
  22. Replies
    19
    Views
    1,001

    So what is the problem, we both have 200 mercury...

    So what is the problem, we both have 200 mercury with identical problem?? Not hijacking and river rat wants me to keep posting also!! Pulled injectors and sent them out this week, will post results...
  23. Replies
    19
    Views
    1,001

    Same problem with 1996 200 EFI

    I am having the same problem. Have u had any success fixing the problem???? Friend of mine is a parts changer and he thinks it may be the injectors. Suggested we pull them and ship them for testing....
  24. Replies
    12
    Views
    845

    Re: Braid tough on equipment? (jejb)

    I have been using braid for many years and have never had any type of problem with reels or guide wear. My reels and rods go from cheap to very expensive. the only problem I have ever had using braid...
Results 1 to 24 of 24