Can the HDS Pro sync feature work with an AT 1 unit
Type: Posts; User: jthomp47
Can the HDS Pro sync feature work with an AT 1 unit
will the HDS pro sync feature also work with an active target 1 unit?
I put the Airmar P79 in my 2009 Ranger Z520 years ago and it has worked fine thru multiple generations of Lowrance units. It has only 2 frequencies 50 and 200 Khz.
With 3 n 1 transducer on the Ghost do you need to flip the left and right image or not? could be confusing if you do it wrong.
I had similar problem with my trailer brakes on a Rangertrail and after a lot of troubleshooting I finally found the problem was a broken blue wire within the trailer plug. Replaced the plug and...
I didn't realize that all three surface are used in every configuration. So the module "stitches" the data from the three surfaces into one image on the MFD
The active target transducer has 3 elements or surfaces. The one that is flush or parallel with the housing is that used for both downscan mode and scout mode? The angled elements I assume are for...
I also had this same brand get water intrusion and had to replace the BMS. Also agree water got in thru the voltage display unit. I made sure to seal it inside and out. so far so good.
I've used a stark (precursor to ionic) 80 ah and 100ah lithium battery to start my 2009 250 etec HO for several years without problems .
Okay found the correct wear sleeves and replaced. Used emery clothe and cleaned the spindles the best I could. Reused the old UFP hubs and put in new races and repacked with new bearings. Races...
You are right about the vortex hubs. The spindle is 1 3/8" straight and Vortex hubs are not made for that size straight spindle but I did see a vault hub that might work ...
You are correct. Ranger told me the bearings are L68149 and I measured the OD of the wear sleeve and is 1.68. I think I found a source for the sleeve on Ebay.
I think you are correct. I ordered some replacement sleeves from the trailer parts superstore that are for UFP spindles. They are not expensive so worth a try. Thanks to all for help.
Is there a part # for the sleeves or do I need to remove them and measure or take them with me to parts store? The spindle shaft is 1 3/8 " straight.
I have a 1994 rangertrail single axle trailer. It has many many Minnesota and Canadian miles on it. Because I am retired and need projects to keep busy (covid19) I decided to do my own wheel...
I think I may have to replace the hubs on a 1994 single axle rangerrtrail trailer. Any body know the spindle size? it looks like the spindle is welded on and appears to be a straight shaft spindle....
I got one recently from Russell Marine
Had my boat out this weekend and the remote does work now, thanks for the advice.
Okay thanks, I think this worked . I haven't had a chance to try it out on the water because I can't deploy the trolling motor on my Ranger trailer because of the step. I will let you know when I...
no I don't and I even turned off my cell phone when trying to pair.
Although I am happy with my ghost trolling motor I am having problems with the remote. I am on my second remote and can't get it to pair. My first remote worked for a while then quit functioning....
I used 80ah Stark lithium on my 2009 etec 250 hp for several years without problems then switched it over to my other tiller boat with a Suzuki 4 stroke 70 hp for the last 2 years again without...
Interesting finding. I have had Stark Power Lithium 100 ah batteries for 3 or 4 years. My 3rd one is maybe 1 or 2 years old and use those three for a 36 volt trolling motor and recently bought an ...
I had to take my screen protectors off because of the glare and no the screen without the protector does not have the amount of glare that the screen protectors produce.
Things must be different in Norway, my live unit says to go to manufacturer web site to download it won't let me download from the wifi in my live unit. Can you send me a copy of the update?