Search:

Type: Posts; User: mdtritn21

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    12
    Views
    171

    TR 20X 2004 to 2009 with the HP hull on the later...

    TR 20X 2004 to 2009 with the HP hull on the later models. Don't get a 20X2 different slower hull
  2. Thread: Bravo on SHO

    by mdtritn21
    Replies
    7
    Views
    166

    It should be alright then

    It should be alright then
  3. Thread: prop hub

    by mdtritn21
    Replies
    1
    Views
    46

    835265Q02 is the old number and 8M0119081 is the...

    835265Q02 is the old number and 8M0119081 is the new number you may need the forward cone bushing too part number 856163Q1
  4. Replies
    5
    Views
    45

    Did you use the right thrust washer?

    Did you use the right thrust washer?
  5. Replies
    5
    Views
    55

    Yes I'm pretty sure Mike couldn't help him with a...

    Yes I'm pretty sure Mike couldn't help him with a Bullet problem.
  6. Replies
    10
    Views
    1,155

    The price of aluminum is up because of the...

    The price of aluminum is up because of the tariffs on Chinese metal and even if they use American metal made it went up too to what ever price the market will bare.
  7. Replies
    40
    Views
    1,588

    That Vexus is still a tin boat like it or not so...

    That Vexus is still a tin boat like it or not so you need to decide tin or glass..
  8. If it too rough take it up to Kerr you won't have...

    If it too rough take it up to Kerr you won't have to fight any boat wakes there. Some days I don't even see another fisherman or boat.
  9. Replies
    1
    Views
    49

    2.5" under pad

    2.5" under pad
  10. Replies
    23
    Views
    196

    You know something that wasn't even asked what...

    You know something that wasn't even asked what motor do you have on that boat regular 225 opti max, 225 pro xs or 250 pro xs.
  11. Replies
    15
    Views
    212

    If it's running 65 at that height loaded and your...

    If it's running 65 at that height loaded and your not going to put a plate on it learn to drive it and get control of the chine. If you think it will gain anything raise it up and try it because you...
  12. Thread: Bravo on SHO

    by mdtritn21
    Replies
    7
    Views
    166

    The 25 Bravo is probably too small if you were...

    The 25 Bravo is probably too small if you were turning the 27 T1 to top rpm's before.
  13. Replies
    15
    Views
    349

    Did any one tell you that you have to trim the...

    Did any one tell you that you have to trim the motor out after your on plane to increase the speed and rpm's. Try trimming it up until the prop slips or the bow starts porpoising then bump the trim...
  14. Replies
    5
    Views
    184

    Did you try the 28 bravo?

    Did you try the 28 bravo?
  15. Replies
    7
    Views
    166

    1.75" sounds a little high so watch your water...

    1.75" sounds a little high so watch your water pressure
  16. How many PVS plugs are in the prop now? It sounds...

    How many PVS plugs are in the prop now? It sounds like you have all of them open and the prop is blowing out from too much venting as you try to get on plane. Put large plugs in all the holes and try...
  17. Replies
    15
    Views
    212

    4" and up not down. If your set in the top holes...

    4" and up not down. If your set in the top holes now you can raise it one bolt hole and try it but a jack plate would let you adjust it to where it actually needs to be.
  18. Replies
    23
    Views
    196

    12" is too much set back and will probably cost...

    12" is too much set back and will probably cost you some speed. Further back isn't always better.
  19. Replies
    2
    Views
    98

    If you mean the carpeted board at the top just...

    If you mean the carpeted board at the top just make one from a piece of treated 2 x 4 and some marine carpet.
  20. Replies
    7
    Views
    166

    What boat and motor do you have? Right now your...

    What boat and motor do you have? Right now your setting at 5 1/8 above bottom to vent plate the same as Yamaha.
  21. Replies
    2
    Views
    73

    Probably a 25 T2 SHO prop.

    Probably a 25 T2 SHO prop.
  22. Replies
    23
    Views
    196

    10" rapid jack manual is all you need.

    10" rapid jack manual is all you need.
  23. Jordan and Falls are big enough to run it on.

    Jordan and Falls are big enough to run it on.
  24. Replies
    15
    Views
    349

    You would need to drop 2" in pitch with a SS prop...

    You would need to drop 2" in pitch with a SS prop to keep the same rpm's as the aluminum prop. I'd take it to the dealer or a mechanic and let them check if the throttle is opening all the way first....
  25. Replies
    19
    Views
    733

    Slabslobberer you need a 25" tempest not a 27

    Slabslobberer you need a 25" tempest not a 27
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4