Search:

Type: Posts; User: BADMFJ

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    1,939

    "Breath like a fish"!! Mesh down the sides and...

    "Breath like a fish"!! Mesh down the sides and the under side of the arms, moisture wicking, and a buff built right into the shirt
  2. Any one in s fla selling a tandem trailer for a 201 pro elite?

    Any one in s fla selling a tandem trailer for a 201 pro elite?
  3. Replies
    13
    Views
    2,468

    I guess I'm just lucky then. Or maybe just took...

    I guess I'm just lucky then. Or maybe just took my time , used some common sense, a few good tools, a bit of mechanical know how, some ambition and all went smoothly. She stows correct and is...
  4. Replies
    13
    Views
    2,468

    I did disassemble the motor and extracted the...

    I did disassemble the motor and extracted the wires from the shaft while drilling. And as far as not seating, just loosen the thumb screw and adjust as needed. I only took 6 inches off and there is a...
  5. Replies
    13
    Views
    2,468

    When you take the shaft out there is a collar, 4...

    When you take the shaft out there is a collar, 4 screws and the drive gear that turns the shaft. The drive gear sits inside the shaft, on mine the hole was 9/16 in diameter. When you cut the shaft...
  6. Replies
    10
    Views
    296

    My water pressure is 25psi. I will check the...

    My water pressure is 25psi. I will check the carbs and rollers. Thanks for all the great info
  7. Replies
    10
    Views
    296

    6" jack plate and a 25p fury. I can't get it to...

    6" jack plate and a 25p fury. I can't get it to turn more than 5k rpm. Thought maybe the height had something to do with it.
  8. Replies
    13
    Views
    2,468

    I got ambitious and did it myself. Other than a...

    I got ambitious and did it myself. Other than a big drill bit it was pretty easy and basic.
  9. Replies
    5
    Views
    547

    Broward county Florida

    Broward county Florida
  10. Replies
    10
    Views
    296

    Motor depth question.

    I have a 97 Stratos 201 pro elite dc w a 200 Johnson venom. I measured the engine height and I'm at 3 1/2 inches below the pad. Is this the proper height?
  11. Replies
    5
    Views
    547

    Anyone selling a trailer???

    Looking for a dual axle for my Stratos 201pro elite.
  12. Replies
    13
    Views
    2,468

    Fortrex shaft mod?

    The shaft length is to long for my boat. I want to shorten the shaft length of my fortrex. It is at the highest it can go and it's still too deep. anyone ever do this??
  13. Replies
    0
    Views
    115

    I Need a trailer for my 201 pro

    I know this isn't the WTB but, My Trailer has rot and now the rear cross beam has rotted off of frame.I'm Looking for a tandem trailer, pref used and aluminum, but any trailer in good shape will...
  14. Replies
    0
    Views
    262

    I Need a trailer.

    I know this isn't the WTB but, My Trailer has rot and now the rear cross beam has rotted off of frame.I'm Looking for a tandem trailer, pref used and aluminum, but any trailer in good shape will...
  15. Replies
    1
    Views
    224

    I Need a trailer.

    I know this isn't the WTB but, My Trailer has rot and now the rear cross beam has rotted off of frame.I'm Looking for a tandem trailer, pref used and aluminum, but any trailer in good shape will...
  16. Replies
    0
    Views
    594

    Key west poker run 2014

    Any bbc bikers going to key west this weekend?
Results 1 to 16 of 16