Search:

504300


update:

I opened up the drive housing and swapped out the steering motor. I broke on SS allenhead bolt off due to corrosion, but other than that inside of housing looked pretty good. ...

Got a foot pedal and verified the same issue. I have prop speed control but no steering. No voltage from steering leads. So thinking that safely eliminates the head.

So looks like I need a new...

will any minn kota foot pedal work as long as it isn’t Bluetooth? Is it specific to voltage? Thanks

Thanks, I am hoping to find a foot pedal somewhere. The company that sold the board is recommending swapping out the drive housing before i install a new board. Will let you know what I find out

I Thanks! I do have a spare remote and just tried that and not getting any repsonce from the steering of auto pilot- anchor buttons with it either

No steering response at all.

Yeah, Ill see if I can find a pedal somewhere to borrow. I just tested amp draw again and still getting the same readings. Multimeter set to 10A and running the current though the meter i am getting...

It is an older I-pilot. I only have a remote, no foot pedal . No Bluetooth. I am thinking control board is bad also,. Just worried about putting another one in and same thing happening if...

Have a 24v 80lb Minn Kota I Pilot.

Recently the motor pegged to high speed while using it and wouldn't respond to any controls. I ordered a new control board and swapped it out. I now have the...

thanks! Will put some glue on it and hopefully get back to fishing

swapping out the control board on my minn-kota 24v 80# Riptide and wasn't sure about the reed switch. IS this just epoxied in place? If so what is the best epoxy to use to reassemble and any tricks...

good deal, thanks for the write up. Ill run back over everything following your info and report back

Trying to get a new to me 75hp mercury setup. we have it mounted and new controls and cables installed. However Need some tips on getting throttle adjustment along with anything else to check
...

ok - thanks for the help- Really appreciate it.

Trying to sell it and someone actually asking if it will fit a 225 3L - So thanks for the help

I have a lower unit I pulled from a 2001 200 HP mercury. (2.5L)

What other years and size motors will this lower unit fit?

anyone had issues with them? I have seen a lot of repeat failures very early on (like first 1-30 hours.) Seems like the repairs arent being done correctly or all the problems arent being addressed...

you guys use the whole jar on one bird? Going to be injecting the turkey here shortly and trying it in an infared oiless fryer.

just to follow up, SO far....they are sending me a new actuator which should fix the problem. They said it is improved actuator and would fix the issue. They were helpful and so far I am happy...

I will check with them Monday and see what they say. I will keep you guys updated

closed today. I will try them on Monday. JP was brand new. Just got it a couple months ago, but just got it installed. On a side note.. how do all these companies get...

Ok, Got a brand new atlas JP with a 300hp Suzuki. Finally got it wired up. Works fine in driveway and at slow speeds, but it wont move hardly at all under power. its like the JP motor isnt strong...

is there an substitute for the 3m 847. Cant seem to find it anywhere

i have a flywheel off a model # e200fpxssc.

also have a couple flywheels with # 345 365 stamped on them, but not sure which model these came off. I will look more tonight if you still need one,...

Will a spark plug wire off a 2000 OMC 225 hp ficht cause any issues on a 2002 brp 250 hp ficht? Assume these are just standard plug wires, but wanted to double check. cant think of any reason why...

pretty sure i haev one if championamn doesnt

just an update,

I went thought all my wiring and cleaned my grounds over the winter. Had same problem happen again just alst week. DFI tells me both EMM's need to repaired. I am pulling...