Search:

Have a ETEC 2007 E90DSLSUA (salt water version). It has a single cylinder T&T #5005756. The unit was resealed about 2 years before we bought the boat. The motor and pump work as they should. It will...

Recently purchased a Blue Wave bay boat and am looking for a used CMC 4" set back, 5 1/2" travel hydraulic jackplate with the relays and switch.

461400
Fabricated/welded the steps and "ole man pole" for my 2000 Champ 203. Made both for $200 in materials.

I have a 2000 Champ 203 with the live well pump out. The screen in the live well over time became clogged. Removed it, cleaned it , and reinstalled it with silicone sealer. Also while it was out I...

Up by the Cagle boat ramp area. There was a big fire up there and smoke was very thick ,went a little to close to the opposite shore of boat ramp by the first turn going down the lake.
Was trying to...

Started my claim for hull repair on my 2000 DCX 203. Landed on stump at Lake Conroe (big boat wake) and now have 2 3-4' cracks under driver area. Just in case, :laugh: any one know of a 2000 203 DCX...

Stay away from the tube frame. Will rust out from the inside. Mine is an aluminum I beam trailer from MCClain Trailer in Houston, TX. Has tandem torsion axles, rear surge disc brakes, folding tongue...

Took an Ultrex 2017 model off my brothers boat and installed on mine. Powered it up and the pedal would not move. Tried to turn the head and it went left and broke the cables. Put new cables and...

Had a aluminum trailer made for my 2000 203 from Mc Clain Trailers in Houston for $4000 (tandem torsion axles, surge brakes, swing tongue, tear drop/braced fender, with step pads before and after...

They are the same width as mine. would like to have them. Instead of sending them, maybe we could meet in the middle somewhere. You are 3 1/2 hrs from me. Will send you IM.

Thanks, David

Sounds good. Did the backs tear or just the bottoms?

Do you have both backs? Didn't have any luck finding something like mine. What is the width of the back? Mine is 22 1/2" wide.

Thanks, David

New seats look really great! Talked with Carol at C&O Marine, she is going to check her stock of Champ seats to see if she has something that will match dark blue/gray or silver. Will keep your offer...

I was planning on replacing the driver/passenger seats next year. This has sped up the process. Llebroc mailed me some material samples. I was hoping some Champ owner had some old seats laying around...

looked at this site already. this is the path I'll take if I can't find one.

I have a 2000 203 DCX Champ. Seats are dark blue with silver inlays. The tabs that hold the seat down broke while fishing and on the way home from lake Conroe the driver seat back must have blown...

Looking to buy the steps that mount to the trailer frame by the winch. Getting older and the steps make it a little safer getting up and down. Brothers Skeeter trailer ( Ez-loader ) has them and they...

Thanks for all your info and the pics of your work. Took the motor, jack plate, trim strip and fuel tank out/off of boat. Drilled all the knee braces in a couple of spots on top and one in the corner...

I know it has some moisture in it, but when I tap around it it all sounds solid. Right now everything is off of the transom. Don't see any rot or soft spots where the trim covered it either. Inside...

My 2000 203 Champ has the wet transom problem. Do you still do the repair? What is a fair cost estimate on this type of repair? Any other options out there to dry the transom and save it? Any...

Noticed some brown water coming from my tie down bracket. Took motor off and have some issues with one bolt hole wet and water seeping from crack at bottom of jack plate. If you don't mind what was...

My spare prop use to sit in the same area as yours. The boat came with a storage "box" looking assy. from Champion which sits in the garage now. Bought a prop bag from Russell Marine Prod. which is...

This is the one I'm looking for . http://im1.shutterfly.com/media/47b9dd36b3127ccec6f78ef5cc5500000040O00BcNHDJy2Ysge3nwI/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

there is another picture on the same post before that one.

thanks, David

Seen an old post from bass boat restoration forum with a picture of a manufactured rod butt holder for passenger/boater rods. Anybody have any info on this :praying:? Post is from 2009

Thanks,...