Search:

Type: Posts; User: hevysrf

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    111

    Thanks, not the one I remember, it was a very...

    Thanks, not the one I remember, it was a very long thread, went over just about every moving part and system on the outside of the motor, the OP had several youtube of his motor starting, but not...
  2. Replies
    2
    Views
    111

    Looking for a thread, 60 ° idle problems

    There was a great thread where Championman walked someone thru almost every step of diagnosing a poor idle stalling condition on a 60° motor, many posts, ended up torn hose behind VRO. Great...
  3. Replies
    0
    Views
    110

    2004 115 txrd low speed miss

    I've got a low speed miss/shake, at no wake speed, about 950-1200 rpm. Just about where the butterflies start to open. 1350-1400 it smoothes out. Will the mixture screws affect operation at this...
  4. Replies
    0
    Views
    97

    2005 Yamaha115TLD idle adjustment

    New to me engine, never lake tested. I've cleaned the carbs and changed the fuel filter, new plugs, fresh fuel.

    When idling in a barrel the rpms are low about 575-600 unless I advance timing a...
  5. Replies
    0
    Views
    133

    Rebuilds and carb jets

    J90 PLRSS
    Looking at installing a rebuilt block, and have read that it is wise to increase the main jets. It seems they supply the same block for both 90 and 115. The one I am purchasing is .020...
  6. Replies
    13
    Views
    347

    Its not the intake, but the crankcase to cylinder...

    Its not the intake, but the crankcase to cylinder block joint, that's leaking.
  7. Replies
    13
    Views
    347

    Port, starts just under #2. Pulling #4 plug...

    Port, starts just under #2.

    Pulling #4 plug wire or stopping airflow to # 4 carb didn't affect idle.

    I guess that red sealant means some was in there already.
  8. Replies
    13
    Views
    347

    When I removed reed assemblies, I noticed a leak...

    When I removed reed assemblies, I noticed a leak where the front half attaches to the block.

    While turning the crank with a socket you can see bubbles right where the new red sealant stops.

    I...
  9. Replies
    13
    Views
    347

    Not yet, I will have one by the weekend.

    Not yet, I will have one by the weekend.
  10. Replies
    13
    Views
    347

    Thanks, linkage doesn't look bad, but I still...

    Thanks, linkage doesn't look bad, but I still can't get it to idle. Fine on Quick Start, then it just seems to slow to a stop. Even if throttle opened. Bowls are full of fuel when this happens....
  11. Replies
    13
    Views
    347

    I may be making some progress, I disconnected the...

    I may be making some progress, I disconnected the oil feed and ran premix from a portable tank, 100% improvement. I guess it was oil rich, not fuel rich, could explain why mixture adjustment didn't...
  12. Replies
    13
    Views
    347

    I'm thinking the floats are ok because the primer...

    I'm thinking the floats are ok because the primer bulb gets solid after a few pumps.

    I never did a sea trial on this boat, not sure about the previous mechanic competency, as the prop did not...
  13. Replies
    13
    Views
    347

    2004 90 Johnson carbs rich ,PLSRR

    New to me engine, compression near 100 on all 4, plugs were light brown.

    Carbs were leaking from bowls, black gaskets. Removed carbs, cleaned, then installed new bowls, new brown gaskets.

    I...
  14. Replies
    1
    Views
    127

    V-4 Prop hardware

    J90PLSRR, trying to fit a 176214, 14 x 17 prop. Nylon 13 spline 0315810 is the part number that shows up in exploded diagrams, but it just doesn't seem to fit corrrectly. Can someone point me to the...
  15. Replies
    4
    Views
    340

    Re: 1990 pro 50 2 stroke, poor aceleration (hevysrf)

    Problem fixed, # 3 float would not shut, debris inside. Don't ask me how it got past the filter. MartyD
  16. Replies
    4
    Views
    340

    Re: 1990 pro 50 2 stroke, poor aceleration (hevysrf)

    Check out the carbs first. A needle may be sticking. If you have fire at all plugs, CDI is good.
    If it's got resistor style plug caps do an resistance check on them
    pull the carbs off,clean them,...
  17. Replies
    4
    Views
    340

    Re: 1990 pro 50 2 stroke, poor aceleration (hevysrf)

    New coil came from boat parts.net , seems to be resistor wire, has double the resistance of the old ones, will this be ok to use? Thanks MartyD
  18. Replies
    4
    Views
    340

    1990 pro 50 2 stroke, poor aceleration

    Motor is new to me this season, idles nice on hose, starts easily, hot or cold, has fresh plugs. Hesitation when trying to get on plane. When at idle in gear, at 800 rpm in water, pulling ...
  19. Thread: 2001 115

    by hevysrf
    Replies
    0
    Views
    154

    2001 115

    Is a 2001 Suzuki 115 4 stroke, a carb or fuel injected motor? Thanks MartyD
  20. Replies
    0
    Views
    364

    Small motor question

    I'm downsizing this year and don't have much experience with smaller motors. I found a 1996 2 stroke 15 REDS Evinrude for my 11.
    What temp should the head be idling on ear muffs? Teltale stream...
  21. Re: 135 Ficht ram FSXSS Vin#GO4861103 Evinrude (LIQUID NIRVANA)

    Look at ebay auction 190153704631, and make me an offer, it wasn't cheap ,but I have already shipped a 1998 175 Ocean Runner to Norway in pieces. MartyD http://xs-s.com/zf/images/smile/emthup.gif
  22. 135 Ficht ram FSXSS Vin#GO4861103 Evinrude

    Looking for input on this engine, low hours, on a nice boat. Personal OMC experience has not been good, and Ficht hearsay is scary. Looks like motor has devalued boat to nearly a hull only price. ...
  23. Re: 1998 Evinrude 175 carb , hesitation on full throttle (ChampioNman)

    Thanks for trying Rusty. The fuel restriction alarms stopped when I put a clean filter in. MartyD
  24. Re: 1998 Evinrude 175 carb , hesitation on full throttle (RUSTY63)

    If your asking if I think its fuel or spark, I don't know. It happens when I give it more throttle. the motor loses its smooth exhaust note, and hesitates before it picks up rpm. thanks .MartyD
  25. Re: 1998 Evinrude 175 carb , hesitation on full throttle (RUSTY63)

    I think its the motor , I tried a different prop for a while, renegade 17,and it didn't change. It happens mostly under a heavy load, like towing a tube or with a lot of people in the boat, The boat...
Results 1 to 25 of 29
Page 1 of 2 1 2