You know, the more I have that about this, I will just go on record here long as it is allowed to stay lol. I am sorry I was basically called a liar and just stood my ground here on things I know...
Type: Posts; User: Jeb_H
You know, the more I have that about this, I will just go on record here long as it is allowed to stay lol. I am sorry I was basically called a liar and just stood my ground here on things I know...
The very reason I called these guys first here locally. I am sure my limited budget won't afford me the best product, but past customer service over the years and a nice shop gets me back.
Yes, I guess you can say that, but was after this person said insult to me first on another topic of this forum.
But you guys can color me whatever color you choose and barbecue and eat me if you...
Carbs to lean on that side of the motor? That or something blocking cooling water.
Your sure the stat on that hot side is opening, heck just for FYI swap sides with the T-stat's that will tell...
Yes, and the really nasty part of this was they talked about taking this rotary motor and use the direct injection (DI) technology on it.
The issue with this rotary motors is the exhaust...
I too like the raw metal finish. I get that hole saw stuff the drill press run way to fast and those hole saws once past 2" will snag a destroy all you hard work in a flash, might even bite you if to...
60 weeks wait time dang that's bad. Like all the trolling motor and electronics you have done. Those are what reads to be great gear.
Jackplate a must have as well. Now your carpet, you seen in...
This is the decal on mine.
Really nice job on that man. You have to be pleased. If not you should be. Heck if you really have issues have it powder coated. I think it's really nice work as it is and that took some time to...
This can be a common problem sooner or later. No biggie, as mentioned already in the sun while hot you can pry that rubber insert out to get to the screws.
I also like to put 3M - 4200 on the are...
Use a regular bearing press and a little soap on the new hub, works wonders pressing the new hub in.
Good looking prop, and the best ones always start out a little to small, then you work them...
This is all good info. I know we need to be buying these new on board smart chargers. That's for sure, then we have to set them up once to get them to see which batteries we are using. These new...
Now this is straight from the text, but you have one sensor with one wire the other with two. Test these like this if questions. Why it's always good to see Temps from a good temp gun. But this...
The hot drag racers have been using just a little water for years. You think this chemical we have now doesn't work or worth it, just think about how rough that is and they were doing this on purpose...
Man to replace it ain't going to be easy or cheap. I would like one of the new 250 Suzuki motors, not near enough trade-in there for my budget. I will just keep my 3.1 for now.
There are those...
To many of the rubber diaphragms fail because of the alcohol in the fuel, then the power of the pump is defeated slowly over time.
Once this happens the oil being thicker and harder to draw...
That sounds to me you need to look elsewhere, least for quick look. Could check voltage on cranking battery, then fire up and see how the voltage looks. All this with a good volt ohm meter. You...
Man you put your hand on both heads at the top to make sure, if no temp gun. I would still be double oiled at this point. Heck I don't trust the VRO's that much. Just say'n
There are several things that are made where they sit turned off, and have a small draw on the battery. You guys are square on with the GPS units, we have gotten to where we here, just remove the...
I feelyour pain man, I got hydraulic steering on my old 2001 Triton and I am not a fan. I wish I had the old steering cable system on my rig,
Man I get the issue of trying to match our guages. I like some of the Faria and Meade guages really well, they just don't make a full set for my boat.
We are needing more info here. Overheating, your getting this going down the lake at speed, how bout at an idle, now at idle I am talking about you on the trailer sitting in the lake at idle from it...
My spell check and fat fingers are not helping here either
You guy are hilarious and so square dead on, heck everyone of you. Heck I have been lmaoff to the point I can't type, which everyone on this forum that has not been an issue. Maybe some of you even...
XXX- Man now that looks like something. Something you can use also. I do have me a new water pressure guage on its way, oem Yamaha water guage. It's so hot here right now, I dread installing it. I...