One thing I will say. You don’t need more than 75amp hour for trolling motor batteries. The new motors being brushless use a lot less power. I have 3 75 amp hours and I rarely use half the power in...
Type: Posts; User: Outofsightpdr
One thing I will say. You don’t need more than 75amp hour for trolling motor batteries. The new motors being brushless use a lot less power. I have 3 75 amp hours and I rarely use half the power in...
Only benefits i see with lithiums is hole shot and the longevity with charging. Speed loss depends on boats. skeeter and phoenix will definitely lose some speed. Also litmus can really mess up...
No way would I switch to lithium for starting. Stay with AGM. U will lose speed switching to lithium. I’ve had a Zxr 21 and zxr20 both with lithiums. Wish I just would have stayed with AGM’s.
I’ve tried all levels of trimming. I also have an atlas hydraulic jack plate. I’ve tried all heights. Best performance I’ve seen is what I posted above. Only thing I can think of. Is that I’m not...
What boat are you running? I’ve seen where they are putting 24p on the zxr21’s this year. Used to come with 25p
Yes. The marks line up perfect and maybe a 1/6th past.
Low 70’s is fast enough for me and that’s what the boat should do stock. Would like to see those numbers. If I didn’t sell the boat every year or two I would definitely flash it.
Exact same. 3 lithiums TM 1 lithium electronics 1 31agm cranking and acc.
I recently purchased a 2024 zxr20. I’m not getting the proper rpm’s. Most I’ve seen is 5550 with stock t2 25p. My brand new back up scorpion 25p will only get 5450. Top speed I’ve seen is 70.1 by...
My 2024 250 sho revs to 3300 rpm’s when it first starts…just for a second. It also is idling faster than normal when in gear. I adjusted the hot foot to where it’s not that. Any suggestions
If running a hyd JP run it a little high and keep trimmed down till u hit around 35-40 mph. I have a 22 zxr21. If I trim any before I hit it he mid 30’s it will propose some. That being said....
I wasn’t sure about his comment so I just left it alone. I’ve always done my best to know what is the best prop
to pad for all my other boats.
Yeah. I just want a true measurement. That way brands and miss calibrated gauges don’t come into play.
What prop to pad are most finding best for Zxr21 with a Yamaha t2 25p? Want measurements …not gauge or hole mounts.
I soak all the bearings in cleaner while using the ultrasound and then spin them while blowing them out. I only use a small amount of oil.
I have a hedgehog studio pin remover. When I clean all the bearings and re oil them evething works great for awhile. Some have said no need for new improved bearings. Just keep the stock ones clean...
How long do bearings usually last in reel? I have some bantam MGL’s that I clean regularly. I thoroughly clean the bearings in a ultrasonic machine and lube when clean. They just seem to need it...
Be careful with boaters advice on JP numbers. I’ve seen where the motor has been mounted on the plate in different holes. Best to always go by prop to pad and start from there. If you do use...
I have a zxr 21
t2 worked prop. Tourney load,3/4 gas and boater 250lbs. 71 add non boater boat does 68 all day. Most I’ve seen is 69.5 with co angler.
Thank U
468750I picked up my new 2022 zxr21 several weeks ago. I bought it from russell marine products in Kansas. Great experience and their rigging of the boat was top notch. Give them a call if your in...
#10Today, 10:05 AM
Prop to pad zxr 21.
I recently purchased a 2022 zxr21 with atlas hydraulic jack plate. What is the best starting point when measuring prop to pad. I read a lot of people On...
Prop to pad zxr 21.
I recently purchased a 2022 zxr21 with atlas hydraulic jack plate. What is the best starting point when measuring prop to pad. I read a lot of people On here stating my number...
I disagree. About every g Loomis there is. I actually like the IMX’s better than my GLX’s. E6 were ok. I think there were a lot of rods that were it’s quality and feel for a few dollars cheaper.
Perfect. Thank U