Search:

The trim seemed to jump me around 2mph each time I hit it up a tap so if anything you think dropping it 1/4 inch would be best place to start after the plugs are in?

I took my ranger out for a ride today to test a new 25p temptest plus. Got the jack plate set at 3.5 below pad and motor is a early 90s 150 xr4 with a 175 power head. I hit 63.8 @5600 and barely had...

Thanks guys. I think I’ll run it how it is now and if it becomes an issue I’ll remove the jack plate

Didn’t get a chance to take it out today but spoke with a guy at ranger and he said the 6” jackplate along with an extra battery is likely the culprit but it shouldnt hurt anything performance wise

Mine doesn’t seem to far off from his actually. I have a 6” jack plate and 4 batteries back there and about 4 gallons of fuel in each tank. I’ll get a picture posted tonight

Boat has had 2 previous owners and both have stored it in garage or a barn. I actually still talk with the previous owner about when I see him in the store around town. He claims it’s always sat low...

So you don’t think filling the fuel tanks will help? I’d rather not get rid of this 36v system. Maybe relocate one battery to under the deck extension? So far I don’t have an issue getting to plane. ...

Every time I have it on the water the bulge pump never pumps water unless I swamp the back(rookie here). When I pull the plug nothing comes out either and running hand in bilge area and bottom of...

Actually the water line at bow is closer to 20” from rail

I will a 90 361v with a mercury 175 and a 36v terrova. I notice when the boat is in the water the water line is about 2 inches from my bump rail at the stern and about 12” from the bump rail on the...

I’m going to try and find one locally. If not I’ll buy the cdi and see if it fixes

Key on the the purple wire from harness to the block that has two posts is 12v. When I attach the purple back to it it’s only 11.51. The other post that has the black tan with blue and tan lines...

Awesome. Thank you joe

Ok so I started in the driveway and beeper still beeps. Took the volt meter to it and the brown and blue stripe wire had 12.57v with key in the on position. I disconnected the purple wire and there...

Thank you and don for your help. I’ll post an update when I get it back running

Thank you joe. Can I ask what exactly is the water cooled regulator?

Thank you joe. Can I ask what exactly is the water cooled regulator?

Either a rotation sensor and coupler or an oil alarm module If it’s high 40s today I might take into the ramp and attempt to start it and see if beeping continues after new plugs

also so would...

Also any idea on a estimated year or serial number range I could use to get parts? I have a quick silver water pump 46-96148A 8. Will that work?

http://www.bbcboards.net/attachment.php?attachmentid=321029&stc=1
The gear seems to look like it’s a spiral type gear and not a cog gear correct?

I removed plugs and checked the coupler rotation and then removed coupler and drive shaft to examine the gear and all seems fine. I took a picture of the gear but it’s pretty hard to see but all...

Will do guys. I’ve checked the gear before and all was good but will see if coupler spins

Thank you very much

http://tinypic.com/r/oizmtw/9

http://tinypic.com/r/119a23l/9
http://tinypic.com/r/33p3edd/9
http://tinypic.com/r/2qs4etw/9
and here is what the boat looks like

http://tinypic.com/r/2uh25qg/9

Nice talking with you also. I will post some pictures here sometime in the next couple hours. I searched the motor over and over and plugs are bare except the one that says 175 and an aluminum one...