Search:

Type: Posts; User: shuclan

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    100

    I meant Garmin Force Kraken ... Auto correct...

    I meant Garmin Force Kraken ... Auto correct changed Kraken to leaked...
  2. Replies
    3
    Views
    100

    I have a Bluetooth capable ulterra that I just...

    I have a Bluetooth capable ulterra that I just took off of my boat. It's a 24volt, 80 pound thrust, I-pilot link, 60 inch shaft, US2 transducer. I did have an MDI transducer attached as well, and I...
  3. Replies
    17
    Views
    2,744

    Thanks for the quick reply, Wayne. Of course, my...

    Thanks for the quick reply, Wayne. Of course, my biggest issue will be that the Mega SI+ transducer on the transom will be useless without the Helix 9 Mega SI+ at the console. I think I'll have to...
  4. Replies
    17
    Views
    2,744

    Wayne, My apologies if this has been asked. I...

    Wayne,
    My apologies if this has been asked. I have a Humminbird Helix 9 Mega SI+ G3N at my console, a Humminbird Helix 9 Chirp GPS G3N at the bow, and now I'm adding Mega 360 as well. If I were to...
  5. I completely agree with you IceNitro. I tried to...

    I completely agree with you IceNitro. I tried to do the Onix update to version 3.110 and it just doesn't work. The instructions on the "new" website describe how to do an update with a zip file,...
  6. Replies
    4
    Views
    1,492

    Guys, Hope someone can help me. I have an Onix...

    Guys,
    Hope someone can help me. I have an Onix 8SI and 10SI networked and linked to an I-Pilot Link (Minnkota Ulterra 80) utilizing the Bluetooth enabled remote. I have Onix version 3.030...
  7. Replies
    780
    Views
    174,623

    Wayne, I am continuing to have sonar depth...

    Wayne,
    I am continuing to have sonar depth reading issues on my Onix bow unit. When I start up the bow Onix, the depth reads correctly for about 20 or 30 minutes, and then the sonar depth changes...
  8. Replies
    780
    Views
    174,623

    Wayne, I think I would need the XTM 14 20 T for...

    Wayne,
    I think I would need the XTM 14 20 T for the ONIX, unless I got an adapter that would support the ONIX's round plug-in. The problem with using a trolling motor transducer is trying to figure...
  9. Replies
    780
    Views
    174,623

    Wayne, I am looking for some info and/or...

    Wayne,
    I am looking for some info and/or recommendations on the following: I have an Onix 8 CI/SI at the console with SI transducer and standard HB 2D transducer linked with a Y cable and an ONIX...
  10. Replies
    780
    Views
    174,623

    There was a software upgrade for the remote and...

    There was a software upgrade for the remote and controller that I had to install that fixed the problem. All is good now. Went fishing yesterday and everything worked well. Now I just need to get...
  11. Great advice, and I wish I had seen it before...

    Great advice, and I wish I had seen it before shipping my Terrova to a person I sold it to from the swap/sell section. I had purchased an Ulterra, and so I used the same box to ship the Terrova,...
  12. Replies
    780
    Views
    174,623

    I got the Ethernet hub connected to both ONIX...

    I got the Ethernet hub connected to both ONIX units and the Ulterra. I configured the new network and everything showed up with the right versions except the remote, which said version 000.1 instead...
  13. Replies
    780
    Views
    174,623

    Thanks for the help, Wayne and Jimmy. Much...

    Thanks for the help, Wayne and Jimmy. Much appreciated. I am networking both Onix units and my Ulterra through an Ethernet hub, so I am sure I will have a bunch of networking questions as I get...
  14. Replies
    780
    Views
    174,623

    Thanks for the help, Jimmy. I did try a...

    Thanks for the help, Jimmy. I did try a different slot, and it worked. That is interesting that it worked that way, but I won't complain. One question I have though, is whether the CHIRP...
  15. Replies
    780
    Views
    174,623

    Thanks for responding and appreciate the help. I...

    Thanks for responding and appreciate the help. I used the same SD card with the 3.0 and 3.03 files that I used to update my Onix 8 to 3.03. I assume the software for the Onix 8 and Onix 10 is the...
  16. Replies
    780
    Views
    174,623

    I just bought 2 used Onix units, and registered...

    I just bought 2 used Onix units, and registered both with My Humminbird. The software downloads that were shown as available on My Humminbird for each Onix was version 2.0 and version 3.00/3/03. ...
Results 1 to 16 of 16