Search:

Type: Posts; User: Bronzeback

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Morning all

    Morning all
  2. Anyone know if you can pull the upper crankshaft...

    Anyone know if you can pull the upper crankshaft bearing assy without splitting the case?
  3. Found the top crank bearing assy bolts are loose....

    Found the top crank bearing assy bolts are loose. What would cause these to become loose and would this mess bearing up? What are my options now new bearing seal assembly? Can you remove this or does...
  4. Thanks ChampioNman I will do that.. I was doing...

    Thanks ChampioNman I will do that.. I was doing some more checking and the one side of the T oil lines the wire tie is loose. The T is dead center behind the air box under the flywheel. Could this...
  5. 544127544128544127544129

    544127544128544127544129
  6. 2016 Gen1 250HO Oil Leak Under Flywheel?

    Model E250HGLABG
    SERIAL 05467413
    Doing 2nd 3 year service and pulled engine cowl and see oil what looks to be coming from under flywheel. Motor has 225hrs. It's like a black sticky black...
  7. Replies
    7
    Views
    448

    106sv to 126sv worth the 2 inches?

    As the title says. Currently have 106sv abd was looking to go to 126sv. Units for livescope only. Seeing some not happy due to a grainer picture. Was just thinking going to the 12 inch screen with...
  8. Replies
    25
    Views
    1,569

    They had a great thing and started changing them...

    They had a great thing and started changing them and not near what they were. Wish I had a bunch of old originals to repaint
  9. What does everyone do with old electronics?

    So what do you do with out of date electronics. I have some gen 1 and 2s that's not worth much. Have a couple I use on my stump jumper pond boat and on my track sled for gps.
    Or does everyone sell...
  10. Replies
    2
    Views
    757

    Pm sent on gen 3

    Pm sent on gen 3
  11. Replies
    11
    Views
    693

    Does the caliper have a Chrysler symbol on it? My...

    Does the caliper have a Chrysler symbol on it? My 97 calipers came off of a 97 acclaim same as pads. Hub I got from ranger
  12. Thanks same thing I am seeing.. No one has...

    Thanks same thing I am seeing.. No one has measurements for the eye to the shank centerline.. Buddy has some mustad light wire that I think will work.
  13. Looking for Jig Hook with Extended Eye to Shank

    Making a custom walleye jig mold that have larger head size and looking for a 90 degree jig hook that has the eye to shank longer than normal jig.
    Any recommendations?
    Thanks
    Chad
  14. rojoguio...

    rojoguio
    Been crazy busy but took all your advice and followed all you have said. Did repair skin first then cut/ground out transom and replaced with Coosa. Reinforced back to G10 Board and...
  15. If I get the core transom out from the skin (.250...

    If I get the core transom out from the skin (.250 inches) and cut g10 board back approx 6 inches to grind, what or how are we thinking of attaching the new core coosa 26 to the g10 stringers. The...
  16. We're it attached in front of transom where the...

    We're it attached in front of transom where the bolt is has epoxy I'm guessing that oozed out of joint. 482577
  17. So basically the strength of this transom comes...

    So basically the strength of this transom comes down to the two .250in 90 degree bends within the laminated transom one on inside of stringer and one on the outside. Plus the 120 degree bend of...
  18. Cap were I cut is 31 inches wide total cut about...

    Cap were I cut is 31 inches wide total cut about 44. Not sure what you mean by making a tooth. Where cap is over transom was sealed with a clear flexible silicone. Where cap sirs over hull looked and...
  19. 482556482557 Cut out to access otherside of...

    482556482557
    Cut out to access otherside of stringer
  20. I wasn't impressed either

    I wasn't impressed either
  21. PM replied

    PM replied
  22. trying to pm you it only gives me option for...

    trying to pm you it only gives me option for url.. not real savy on getting pics on this site.
  23. Here is a closeup of the right side of transom...

    Here is a closeup of the right side of transom standing behind it.. Notes of where movement has occurred or delaminate
    482500
  24. Got some pics.. ...

    Got some pics..
    482490482491482492482493482494482495482496482497
  25. Little setback on project. Caught a sinus bug. I...

    Little setback on project. Caught a sinus bug. I have to cap cut and removed. I will get some pics up of what I’ve found. Rojoguio thanks for the offer but I already purchased probably way more than...
Results 1 to 25 of 380
Page 1 of 16 1 2 3 4