Search:

Type: Posts; User: Gohawks688

Search: Search took 0.00 seconds.

  1. No cables attached at the moment. Just control...

    No cables attached at the moment. Just control box.
  2. New mercury 150 control box reverse throttle stiff

    In the process of a repower with new merc 150. During control box install I noted that reverse throttle (after reverse gear shift is completed) is pretty stiff. Much stiffer than forward...
  3. Replies
    8
    Views
    299

    Thanks for all the input guys. Right now I'm...

    Thanks for all the input guys. Right now I'm leaning towards running only vessel view mobile on the tablet and ditching all mechanical guages. Don't need troll control ect. Not planning on getting...
  4. Replies
    8
    Views
    299

    New 150 4s analog guages?

    Please forgive me if I am posting in the wrong forum.
    I am in the research portion of a repower of a 1999 bayliner trophy with a 150 merc 4s. Currently powered by a 175 2 stroke carb.I am to the...
  5. Replies
    12
    Views
    563

    Meter was right I've done continuity tests many...

    Meter was right I've done continuity tests many times
    I get not continuity no matter what position the float is in. Full up or down.
  6. Replies
    12
    Views
    563

    I did more testing on the oil cap sensor. the...

    I did more testing on the oil cap sensor. the manual states " disconnect both low oil sensor leads. There should be no continuity between the leads. If continuity exists then the sensor is faulty."
    ...
  7. Replies
    12
    Views
    563

    Ok so i bought this module and installed it....

    Ok so i bought this module and installed it. <EDIT- Unsupported Products>
    everything went smooth except that there was a splitter provided for the blue wire that goes to the oil plug cap sensor. the...
  8. Replies
    12
    Views
    563

    Serial number 0g804616 I was testing power from...

    Serial number 0g804616
    I was testing power from the module to the rotation sensor with he bullet connectors unplugged. No DVa for this test. Key on engine not running. The manual was not specific...
  9. Replies
    12
    Views
    563

    175 oil alarm

    Ok guys I am having an oil injection alarm on my 1999 mercury 175 two stroke salt water series. If needed I can provide serial number. Upon start up it has a continuous beep beep beep alarm. I have a...
  10. Ok so I'm on the process of testing the ignition...

    Ok so I'm on the process of testing the ignition components per the manual. I got a dva adapter. I am having trouble measuring the voltage input to the coil. It is jumping all over the place. I...
  11. Wow I guess I'm defaulting to old carbed car...

    Wow I guess I'm defaulting to old carbed car engines that need voltage to the coil/points.
    So does the key switch ground out the coils/if ignition to kill the engine? If that was the case could the...
  12. Sorry my serial number is OG804616. I guess I...

    Sorry my serial number is OG804616.

    I guess I didn't put two and two together with regards to Joe's comment. How does the engine run with out signal from the key to the ignition? And how does it...
  13. thanks guys i will look into that. i will check...

    thanks guys i will look into that. i will check the main plug on the motor and clean for corrosion/good connection.
    As far as the boat harness killing the motor I have a few thoughts on what it...
  14. I forgot to add that when I cleaned the carbs I...

    I forgot to add that when I cleaned the carbs I pulled the intake and checked the reeds. they looked ok to me, no obvious damage. I am new to two stroke and outboards however.

    could this be a...
  15. Merc 175 cuts out randomly, able to restart instantly

    Howdy all,
    I've got a new to me 1999 mercury 175 carb saltwater series that I am having issues with. It likes to suddenly die on me ( like you turned the key off , not a sputter sputter then die)...
  16. Replies
    12
    Views
    1,339

    Can anyone give me the run down on setting the...

    Can anyone give me the run down on setting the timing with the software? I am a points distributor kinda guy and the manual just says use the software.
  17. Replies
    12
    Views
    1,339

    I have removed the filter and rinsed out with...

    I have removed the filter and rinsed out with carb cleaner. Didn't remove the sensor from the filter. Will give it a try.
  18. Replies
    12
    Views
    1,339

    more troubleshooting updates today... started...

    more troubleshooting updates today... started working my way through the manual starting at fuel.
    ran the static fuel tests. pressure at both Schrader valves on the vapor separator check out 2-10...
  19. Replies
    12
    Views
    1,339

    Thanks I will run the capacitor test today! I...

    Thanks I will run the capacitor test today!

    I know the batteries are a huge deal. That's why I went out and bought a new one. With the old ones I was not getting spark at all. I am using the brand...
  20. Replies
    12
    Views
    1,339

    Hmm that would be great if it's ok. That was my...

    Hmm that would be great if it's ok. That was my biggest worry so far. Don't want to run it without oil. I had a hard time googling that symptom though.
  21. Replies
    12
    Views
    1,339

    I was going to pull the lower to do the impeller...

    I was going to pull the lower to do the impeller once I get it starting reliably, I will check the shift rod height once I do that. I don't think the shift switch should have any effect on starting?...
  22. Replies
    12
    Views
    1,339

    evinrude ficht 150 hard starting cold

    Hello all,
    I am trying to trouble shoot a 98 ficht E150ILECR serial number G 0440109 . The symptoms are hard starting. my dad told me that it wont start cold unless primed with gas/oil into intake....
Results 1 to 22 of 25