Search:

Type: Posts; User: Outboard123

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    315

    150 Fourstroke Won’t Trim Up

    Have a 2014 150 fourstroke (serial #2b082617) that will not trim up, I replaced both trim relays and no change, not only does the relay click, it clicks multiple times and almost makes a buzzing...
  2. Replies
    3
    Views
    392

    Correct, the starter does not activate when this...

    Correct, the starter does not activate when this happens, I will check voltage at the starter next time it does it. I have been told after I have ran the engine really hard I should idle for a few...
  3. Replies
    3
    Views
    392

    150 FourStroke

    Have a 2014 150 fourstroke (serial #2b082617) that will not crank after running very hard (pulling kids on tube), the engine has never died on me or gave an alarm, it runs great but after I shut it...
  4. Replies
    0
    Views
    138

    Water Tube Spacer

    What is the purpose of the black plastic piece that falls out when removing the lower unit on some Suzuki outboards (typically 300hp)? I did some research and it seems to be called the water tube...
  5. Replies
    39
    Views
    1,113

    One last flywheel question and i will officially...

    One last flywheel question and i will officially move on, anybody ever seen a flywheel that looked good visually but was still bad? From what I understand if a flywheel is bad it will be obvious as...
  6. Replies
    39
    Views
    1,113

    I agree that the service manual is a must have...

    I agree that the service manual is a must have and very helpful when troubleshooting but there's also good info that's not in the service manual that someone with expierence knows. Like I said, even...
  7. Replies
    39
    Views
    1,113

    Update - this motor did indeed have the wrong...

    Update - this motor did indeed have the wrong flywheel on it (customer had been trying to diagnose and was borrowing parts from friends and i believe he got confused with what was what) and timer...
  8. Replies
    39
    Views
    1,113

    Found the flywheel magnet orientation chart on...

    Found the flywheel magnet orientation chart on CDI's website, the flywheel marks line up with the picture from the v4 & v6 1986-1987. But pretty sure this motor should fall under the 185/200/225 V6...
  9. Replies
    39
    Views
    1,113

    As the day went on things started getting worse...

    As the day went on things started getting worse again, really thinking it's more of a flywheel problem than anything. Hopefully can find a good used one to try
  10. Replies
    39
    Views
    1,113

    Based off the model number I gave can you tell if...

    Based off the model number I gave can you tell if this is a cross flow or looper?
  11. Replies
    39
    Views
    1,113

    Or they could affect one another?

    Or they could affect one another?
  12. Replies
    39
    Views
    1,113

    We try and use OEM everyy chance we get but...

    We try and use OEM everyy chance we get but sometimes were guilty of getting inpatient and we can get CDI overnight. I apologize if you've already answered this, so your saying the inner and outter...
  13. Replies
    39
    Views
    1,113

    I was kinda hoping adjusting the outter magnets...

    I was kinda hoping adjusting the outter magnets wouldn't fix this motor (because I would be more confused than I already was) but it seems to have fixed it. I epoxied them in their proper spots and...
  14. Replies
    39
    Views
    1,113

    I understand that but the flywheel had the same...

    I understand that but the flywheel had the same results as the other one, all timer base wires had voltage (disconnected) except #5. I'll let you know the results tomorrow after I epoxy the magnets....
  15. Replies
    39
    Views
    1,113

    I tried another fly wheel and timer base (third...

    I tried another fly wheel and timer base (third one including original one) and no change, did notice the magnets on the second flywheel has shifted and some of the magnets are also touching on it...
  16. Replies
    39
    Views
    1,113

    That's the plan for tomorrow, I'm really just...

    That's the plan for tomorrow, I'm really just wanting to better understand the function of the magnets at this point. I've heard the outer magnets control stator output and the inner magnets control...
  17. Replies
    39
    Views
    1,113

    You certainly didn't answer my question either,...

    You certainly didn't answer my question either, the green timer base wire has no voltage while engine is cranking or running. I'm mainly just curious what affects the inner and outer flywheel magnets...
  18. Replies
    39
    Views
    1,113

    The timer base wires are blue, green and purple....

    The timer base wires are blue, green and purple. The blue is top cylinder, purple is middle and green is bottom. Bottom cylinder on starboard side not firing and green timer base wire has no voltage...
  19. Replies
    39
    Views
    1,113

    So the outter magnets being in the wrong spot (or...

    So the outter magnets being in the wrong spot (or touching) wouldn't cause the timer base to not put out voltage? And just say the inner magnet was the problem wouldn't it still put out voltage but...
  20. Replies
    39
    Views
    1,113

    Flywheel magnets

    Working on a Evinrude 200 XP (E200STLCEB). No voltage on #5 timer base wire (green wire), got new timer base and it didn't help. Noticed the outside magnets of flywheel have moved and a few of the...
  21. Replies
    2
    Views
    240

    Evinrude not pumping water

    Working on a 25 hp evinrude (VE25ELESE) and it pees water all day on hose but when you put the exhaust under water (back into lake) it stops peeing and over heats. It's like the exhaust is pushing...
  22. Replies
    10
    Views
    760

    I have a few guys at my shop dealing with the...

    I have a few guys at my shop dealing with the same problem. Still haven't found the cure but I can guarantee it's not the MAP sensor (at least didn't fix the ones I'm dealing with). Let me know if...
  23. XR6 hard to start after sitting at fishing spot for 30+ min.

    I know this problem has been talked about a lot and I was curious if there was ever a found cure. Mercury XR6 starts good first thing in morning, idles good and runs good but when you stop to fish...
Results 1 to 23 of 23