I would recomend deutsch connectors or AMPSEAL 16 If you are going to spend the time and money to redo the connections on any of your electronics I would recommend. They are affordable and provide...
Type: Posts; User: Slim95
I would recomend deutsch connectors or AMPSEAL 16 If you are going to spend the time and money to redo the connections on any of your electronics I would recommend. They are affordable and provide...
This should work with a remote switch on the dash.
https://www.te.com/usa-en/product-1416010-1.html
I have a couple suggestions regarding the terminations. Remove all the colored nylon on your crimp terminals slide some adhesive lined heat shrink and seal all the terminations. All your wire needs...
I ordered an automotive set (moroso) for my 250xb from summitracing and cut them to the same length as the factory ones. Everything worked out great and have a little over a year on them. I came from...
I run power to the circuit breaker then to the switch. I turn the switch off eveytime the boat is not in use and never like the idea of using the breaker as a switch
I will take the alternator and bracket if you still have it
Try it and report back
Do it your self, I rebuilt the whole system on my XB250 a couple of moths ago. A good manual and keeping everything clean. Buy replacement end caps with the seals already installed and save yourself...
There are no directions you are gonna have to get creative. I replace my seats with bassboatseats.com in my tr22. I removed the original seats marked the new holes on the plat form with the new seat...
prowireusa.com, They sell Tefzel wire in all colors and striped colors in all or most AWG, They also sell MIL SPEC wire and true shielded wire.
My bussman panel is in the bilge area. My triton came with an aluminum panel that covers all the pumps, so i cut a square hole in the panel and mounted the bussman. they make two different size...
These are the panel I used in my boat project. I know every one uses bluesea panels but I dont like the fact that bluesea is not really water tight. The bussmans below are a lot more involved a far...
https://www.dbelectrical.com/
I just got a start for my XB from here a couple months ago. So far so good
This is awesome! Thank you for having the mindset of challenge what they say cant be done. And for sharing it with us.
Fishnfireman when do you plan on making this swap? Really wanting to make this swap also but do the SI in-lieu of the DI i currently have.
I was one of the few that the sensor was bad and not the tank. after replacing the oil tank two years prior and not enjoying it opted to just buy a new sensor and test if it worked as it was only...
You need to be more specific on what you are asking.
430094430095430096
I thought this kit was a pretty good idea for connecting and securing if your using this type of cells
https://vruzend.com/product/vruzend-battery-kit-v2-0/
DO IT! Im thinking about doing it this winter after watching the youtube channels on it.
there is a gentleman named Keith on Facebook who has a TR196 with a supercharged flashed SHO and i think he is running 116 now. Before the supercharger and just a flashed SHO I think he was running...
Cut the hose down the middle and be careful not to cut anything else. Leave two or three inches from both flanges and the TH zipper cover will wrap over the the excess hosing you left. Looks clean...
I run the highest grade fuel I can find at the pump which on average is 93 with ethanol. Yes I did wire the electric fuel pump to the ignition with a relay. I was tired of rebuilding the mechanical...
I put a low volume Carter electric fuel pump on my XB as I was tired of the same issues. Runs great after it planes out but if I idled to long in gear sometimes it would die or bog down terribly when...
Yes you can install a digital guage and use your existing tach signal wiring. I replaced all my original crappy guages and install a Racepak digital dash and used all my factory wiring