Search:

Type: Posts; User: Crappieguy84

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    113
    Views
    24,155

    Thank you!

    Thank you!
  2. Replies
    113
    Views
    24,155

    Bill, this is a great project. I am interested in...

    Bill, this is a great project. I am interested in what you did to build your autoscan module? What board did you use? Feel free to pass along any information you would like to share.
  3. Replies
    2
    Views
    409

    Todd, thanks for the help here. I can't wait to...

    Todd, thanks for the help here.
    I can't wait to get one of these on here and get my Garmin package.
  4. Replies
    2
    Views
    409

    Garmin Force size

    I’m unsure if this is the correct place to ask this. I am looking to go to the new Garmin Force TM once my current MG XI5 takes a dump. My question is, how far does the Garmin TM stick over the bow...
  5. Replies
    40
    Views
    965

    So I had the DVA come in and did the stator and...

    So I had the DVA come in and did the stator and switch box tests along with the resistance checks on the trigger. All checked out good and within specs.

    I found a test ECU at a local shop, it’s...
  6. Replies
    40
    Views
    965

    So I had the DVA come in and did the stator and...

    So I had the DVA come in and did the stator and switch box tests along with the resistance checks on the trigger. All checked out good and within specs.

    I found a test ECU at a local shop, it’s...
  7. Replies
    40
    Views
    965

    Fuel pressure is good. 36 with key on, drops to...

    Fuel pressure is good.
    36 with key on, drops to 33 after about two minutes with pump off.
    34 while engine is running, did not get a chance to get about 2K rpm as I tested on the hose.
  8. Replies
    40
    Views
    965

    Semper Fi, Jarhead. I added a tiny tach mounted...

    Semper Fi, Jarhead.
    I added a tiny tach mounted on the dash for this exact reason. The Mercury tach is adjusted as close as possible but is still off by as much as 1,000 rpm at times.
    The tiny...
  9. Replies
    40
    Views
    965

    No, I haven’t. Work has called me away til the...

    No, I haven’t. Work has called me away til the weekend. I will check the pressures this weekend.
  10. Replies
    40
    Views
    965

    leonreno, what is the question, I do not...

    leonreno, what is the question, I do not understand .....
  11. Replies
    40
    Views
    965

    Joe/Leon, The motor doesn't look to have any...

    Joe/Leon,
    The motor doesn't look to have any paint missing on any bolt heads for the divider, heads, or really anything on powerhead.
    Looking at the stator from underneath it looks new, my first...
  12. Replies
    40
    Views
    965

    Yes, it was idling on the hose while doing some...

    Yes, it was idling on the hose while doing some checks.
    Any ideas as if this could be fuel related or ignition related?
  13. Replies
    40
    Views
    965

    Here’s a photo of inside the midsection. It looks...

    Here’s a photo of inside the midsection. It looks awfully wet and carboned up to me.
    Am I correct in thinking this?
  14. Replies
    40
    Views
    965

    Leon, timing from 1 was 23*, highest cylinder was...

    Leon, timing from 1 was 23*, highest cylinder was #2 @25* with others inside that variance.
    Hole shot isn’t bad, 5 seconds or less with the Tempest 25P, when I put my 4 blade 24P I have to feather...
  15. Replies
    40
    Views
    965

    I pulled the LU off, all looks good and tight,...

    I pulled the LU off, all looks good and tight, just very carboned up and wet.
    Also checked the fuel regulator screen for debris, it was clean. Pulled fuel lines from pulse pump to separator and...
  16. Replies
    40
    Views
    965

    Joe, I’ll check that later today. That never...

    Joe, I’ll check that later today. That never crossed my mind.
    more details to come.
  17. Replies
    40
    Views
    965

    Joe, no I don’t know anyone that would loan out...

    Joe, no I don’t know anyone that would loan out and ECU. Unless anyone here is in MO, I’m willing to come to them or cover shipping and even pay a small fee to rent it.
    I had sent my ECU to get...
  18. Replies
    40
    Views
    965

    Leon, Verified the .462 mark, and made accurate...

    Leon,
    Verified the .462 mark, and made accurate timing marks for all cylinders on the flywheel.
    I will verify no obstructions in the cowling.

    any other ideas that would cause this to not hit...
  19. Replies
    40
    Views
    965

    Joe, this is a tempest 25p. I tried a 24P 4...

    Joe, this is a tempest 25p.
    I tried a 24P 4 blade and it didn’t change the RPMs much, just gave me a bit more lift.

    what do you think could be causing a rich situation? It makes sense that I’d...
  20. Replies
    40
    Views
    965

    I double checked a few things today, ran some...

    I double checked a few things today, ran some ignition tests with a meter. Link and sync is good, TPS is .245, ohmed out the coils and switch boxes.

    Out of curiosity I checked the plugs, they...
  21. Replies
    40
    Views
    965

    Charger 195 GPS speed is 53 or so with 5000 rpm...

    Charger 195
    GPS speed is 53 or so with 5000 rpm
    trimmed with a rooster tail just below motor height or less
    PTP is 2.75” below
    This is a new to me boat, I have never seen it better.
  22. Replies
    40
    Views
    965

    Checked the intake air and head temp sensors,...

    Checked the intake air and head temp sensors, both checked good, slow to change but within spec.
    I also checked the vacuum line going from the intake to the ECU for the MAP sensor, it was clean.
    ...
  23. Replies
    40
    Views
    965

    Joe, I will check sensors and report back.

    Joe, I will check sensors and report back.
  24. Replies
    40
    Views
    965

    200 efi not reaching WOT

    Engine SN is OG350446

    Issue at hand is not able to turn more than about 5,000 rpm under load.
    115-120 psi on all cylinders
    Injectors flowed and calibrated by Brucato FIS
    TDR Reeds
    pulse pump...
  25. Thanks, Joe. I am running a Tempest Plus 25P.

    Thanks, Joe.
    I am running a Tempest Plus 25P.
Results 1 to 25 of 48
Page 1 of 2 1 2