Search:

Type: Posts; User: ChampioN BASS

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    128
    Views
    12,770

    Hi everyone, any 198 CX / 2010 manual available....

    Hi everyone, any 198 CX / 2010 manual available. I noticed Genmar stickers on wiring harness. Think one of last Build # GCB112901910/198CX
    It would be appreciated
    fpumps@mweb.co.za
    Thank You
  2. Replies
    10
    Views
    704

    Noticed that Bore, Stroke, Comp Ratio, Weight,...

    Noticed that Bore, Stroke, Comp Ratio, Weight, rpm Range exactly the same. The diff pay for the flash.
  3. Replies
    10
    Views
    704

    SHO on Champ

    Hi every one, time to re power my stage 3+ 250 HPDI need a block witch I can't lay my hands on.
    How does a 250 SHO preform on a 198CX year 2010 one of the last ones build. We don't have motor...
  4. Replies
    3
    Views
    559

    HPDI

    Hope it was not sitting all that long?
  5. It does not do the motor any good if warmed up in...

    It does not do the motor any good if warmed up in Neutral no. 2 and 4 not warming up like the rest.
    Would be far better if it could warm up all cylinders in Neutral especially in a tournament start,...
  6. Following

    Following
  7. Replies
    14
    Views
    1,022

    Like LES YOUNG said You goanna Spend a lot of...

    Like LES YOUNG said You goanna Spend a lot of $$$$$...we all started off with "ONE MOLD"
    It became a sickness a Good One though.
    Welcome to lure making ENJOY
  8. Replies
    2
    Views
    328

    Sounds like fuel, start with lift pumps. Replace...

    Sounds like fuel, start with lift pumps. Replace with Electric pump. Replace fuel lines and add water separator / in line filter.
    I feel your pain, those are good Hours though.
  9. Replies
    9
    Views
    911

    He is at a Better Place thanks for what you have...

    He is at a Better Place thanks for what you have done.
    R.I.P
    Prayers to His Family and Friends
  10. Replies
    33
    Views
    1,860

    YAM911 JY SAL VERBAAS WEES

    YAM911
    JY SAL VERBAAS WEES
  11. Replies
    33
    Views
    1,860

    Did you find anything that could have caused the...

    Did you find anything that could have caused the failure?
    Keep in mind when you rebuild to have that motor balanced, you will be surprise and ask the balancing shop to give you the weights.
  12. Replies
    33
    Views
    1,860

    You lucky to got that far my 08 series 2 popped...

    You lucky to got that far my 08 series 2 popped at 82 hours. Then its a mischief, not to know what the cause was make it no better. Re Build or send it to have it done.
    I will re build mine till...
  13. Replies
    33
    Views
    1,860

    Was the motor worked on Before?

    Was the motor worked on Before?
  14. Replies
    33
    Views
    1,860

    Those pit marks is from shrapnel getting squashed...

    Those pit marks is from shrapnel getting squashed in the Squish Band and they get there through the transfer port.
    If it was run for longer some more pistons would have shown squashed (PIT) marks. ...
  15. Replies
    33
    Views
    1,860

    I would say the bottom end gave way first that...

    I would say the bottom end gave way first that were the piston / bore score come from. Maybe a cap bolt or the bearing first. Luckily those rings did not open that could have been a block.
    Sad news...
  16. Replies
    33
    Views
    1,860

    Correct me if I'm wrong Oil enter at intake after...

    Correct me if I'm wrong Oil enter at intake after throttle body on to the crank and to all cylinders at same time. Oil pump failure would leave all bearings and cylinders dry. Oil mix in Vast then...
  17. Replies
    8
    Views
    616

    Exhaust port Hight differ as well not sore about...

    Exhaust port Hight differ as well not sore about throttle body though.
    While you at it go 300
  18. Tape the sides up to ported paint should your...

    Tape the sides up to ported paint should your blade touch, cut them of and turn them around, if used a std 304 Stainless Steel Shank bolt with nylock nut and some Loctite for peace of mind.
    Good Luck
  19. VERY NEED Job there

    VERY NEED Job there
  20. Thread: 250 HPDI

    by ChampioN BASS
    Replies
    4
    Views
    762

    Thank you Yam911 I got a motor same model...

    Thank you Yam911 I got a motor same model VZ250FTLR serial no's 10 apart
    Mine 1005719 and the author 1005709
    700 km from here but closer for a match will be hard to find.
    Thanks
  21. Thread: 250 HPDI

    by ChampioN BASS
    Replies
    4
    Views
    762

    Sorted please Remove

    Sorted please Remove
  22. Thread: 250 HPDI

    by ChampioN BASS
    Replies
    4
    Views
    762

    Sorry full no. VZZ250FTLR

    Sorry full no. VZZ250FTLR
  23. Thread: 250 HPDI

    by ChampioN BASS
    Replies
    4
    Views
    762

    250 HPDI

    Can any one tell me if parts will be interchangeable between these two motors. Plan is to use as spares.
    FLTR250 /07
    and
    Z250FETO /04
    Thank You
  24. Replies
    161
    Views
    17,980

    Ride and Deside

    Ride and Deside
  25. Replies
    16
    Views
    5,302

    Only way to compare apples with apples take to...

    Only way to compare apples with apples take to Stock Motors fit with the diferent flushed ECU's and run on the Same Dino under Same conditions.
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4