Thanks for the replies!
Type: Posts; User: benellishooter3
Thanks for the replies!
looking for ideas on mounting my DI+ transducer on my Ulterra. i have it mounted on the trolling motor but can't come up with a good plan for the cable. i have an air hose around it now for...
Thanks Wayne! Dang it...
Can i run a Y cable to the US2 and mega 360 to my helix 10 di+. I’m wanting 2d and depth and temp on the front unit.
Wicked wacky! I've tried at least 5 different weedless hooks. By far the best I've tried. Also, 3/8 clear heat shrink for the senko, last forever.
Thanks for the heads up. I might call xpress tomorrow, see if they'll sell just the covers. I kinda hate to buy all new seats if I could just recover.
Looking for new seats or covers for my 05 x18. Anyone know if xpress will sell just the covers so I can get them redone with factory look?
If no, anything important I need to know before...
I'll be there as well. Good luck guys! Let's hope it's not bumper boats and we can actually fish.
The web site states 175?
Dirty connections also add impedance, which adds heat. I had a couple on a bass pro charger come apart. The fuses and holder looked pretty bad. Make sure they're clean and tight, I wouldn't...
235725
You sure can, but I had zero luck with pullers, this is the factory jack off of my power stroke with 500 lb test straps. It took a ton of pressure to get it out! You will have to bend the...
Yeah I should be able to do that this weekend. Shoot me a pm with your email and what you're looking for. Mines completely stripped down. I have diagrams in my service manual too if you need that. ...
Thanks! I've got a service manual and I've got it torn apart, I'm going to price parts soon to do a rebuild. The oil was not milky. There are a couple bearings that seem stiff and not entirely...
It doesn't look like it, and from my research on new parts that bearing is like the cap off of a U joint, the rollers are not attached to the race and the new one comes with a spacer to hold them in...
I need to research it more before buying any replacement parts, I've got the lower completely torn down I just couldn't wait to see what was going on. There's a bearing right above the pinion and...
No water in the oil, I've got the bearing carrier out so I can see most of the gears. I'll probably tear the rest of the way down this weekend. Advice on what to do? Good people who rebuild them? ...
bought a new to me 2005 x18 with a 2004 150 vmax on it last year. finally got to some big water with the boat the last two weekends. a week ago i ran about 65 miles calculating by the mile markers on...
bought a new to me 2005 x18 with a 2004 150 vmax on it last year. finally got to some big water with the boat the last two weekends. a week ago i ran about 65 miles calculating by the mile markers...
I think you should be seeing 50 at least with that set up with correct prop and P to P. But I'm just guessing.
I believe I was told to level the pad and level the motor to take P to P measurement. I think my x18 is 6 inches with 6 inch jack plate, and I can trim all the way up with it that low. But I am...
Thanks guys, the information is appreciated!
All good information. Thanks again everyone.
Thanks for the replies! I was thinking yamalube but I wanted less smoke with semi or full syn. Thanks again!
I've got an 05 back track trailer, just purchased last year. The original owner said he's never changed the bearings. I'm trying to figure out what hubs are on these trailers? It has a zerk in the...
I'm a bit overwhelmed with oils. Ok, I'm running an 04 150 vmax carb. I just bought the boat last year. I've been running some cabelas cheap two stroke oil and it smokes quite a bit. From the...