Search:

I regrease my hubs yearly and I to have found a little moisture in the cap when I removed them, also the grease was a little milkish. I pumped new grease in through the zerk fitting while the wheel...

Alot of talk about having issues on wet days, so I put a thin bead of silicone on top and sides of the power switch and the control panel for livewell and lights.

That puck might be for the flasher, That was probably on the console at one point in time. The hole where the flasher was, might be used for something else if the flasher is not in the console.
...

To remove the wheel, put a deep socket upside down over the stud, while maintaining pressure up with your knees and hand, hit the deep socket a few times and the wheel will pop. less than a minute to...

I just bled my wife's car last night, dip the end of the clear vinyl tubing in hot water to soften it before slipping it over bleeder screw. Use a length of tubing long enough to elevate the bottle...

I had a 185 DC Pro and it had a bench seat. There was 5 screws under each seat cushion.

Ok Boat is in garage and I am looking for the y connecter. Where is it usually located? I looked in the back area and under the console, i traced the console mounted wiring back to the gunnel. There...

Thanks, will check next time boat is in garage.

I have a Mega DI Side imaging Chirp transducer transom mounted with Gen 2 Helix 10 on console and Helix 9 upfront on trolling motor. My side imaging stopped working and depth is intermittent. However...

It was not a dumb part on you, it's a learning curve we all have to master. Now you know for next time, unless you do the same thing. Then it is a dumb part on you. lol

Took me twice too.

Thanks Bryan
I didn't realized i was talking about something different.
Is that the same thing as the holes on the side of the stringers on the outside underneath? Boat is not here, so I can't...

I thought they were for the fuel vapors to escape and not build up and possibly cause an explosion.
He didn't say the fitting went through the hull, just that it was at the bottom.

Supply and Demand In 2019 and 2020 people bought more boats and RVs due to pandemic. The manufactures are trying to capitalize on the market.

I have never owned a nitro before, I have owned a Winner 16 footer with a 115 Suzuki 2 stroke. I have owned a 185 DC Procraft With a 150 Optimax, and currently own a 2019 Z20 with a 250 4 stroke pro...

investigate it
Have someone lift up and down on it while you lay on your back on the floor under the console with a bright flashlight and see what's going on.
Possibly all that's needed is some...

So you're saying this would work as long as you don't go past 50 feet away from the boat? I see your theory in this, problem is the boat will still travel past the length of the leash and drag you...

The hot foot can be adjusted to the rear by sliding the pedal back on the plate. It might not be enough for you.

The wedge might be a structural part of the boat with a pad glued on to it.

10 inch jack plate.

Mine came with a 12 inch manual, so not sure how much difference this makes in performance.

I like your detailed breakdown of weights and performance. I agree with the...

What is the prop to pad height on the original post?

GPS or odometer? LOL

If they are locked out, then how do they brake moving forward? Or you don't use the trailer brakes, since you specified that you are close to the launch.

Is it a clunking noise?
A better description of the noise would be helpful. As BMCD noted, it depends on what you are referring to. (popping and squeaking)
Not sure what you sound you hear when...

In the center forward compartment, I keep 8 3700 boxes on the sides with soft baits. Big compartment in the center of center box has buoys and coffee thermos. front section has sunscreen, oxygen...

Are you looking into multi leaf or staying with single?

I don't know the answer to your question, but just wondering if people are changing to multi leaf springs to help quiet the ride.