Search:

Type: Posts; User: scrutcher

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    304

    Ashmore marine sells536302 one for the z- series

    Ashmore marine sells536302 one for the z- series
  2. Thread: Pro xs 150

    by scrutcher
    Replies
    2
    Views
    157

    Pro xs 150

    Need the hose part# that goes from pulse pump the the 90° fitting that goes in the block (1b916729)
  3. Replies
    13
    Views
    554

    This week3nd I am going to take a trolling...

    This week3nd I am going to take a trolling battery and switch it with my starting battery and see if it charhes to 99-100% so that will tell me if its the trolling side of charger
  4. Replies
    13
    Views
    554

    I will look to verify when I get home later today...

    I will look to verify when I get home later today but I think it was around 13.4v
  5. Replies
    13
    Views
    554

    I havent had an issue in over a year with my...

    I havent had an issue in over a year with my ionics, at first I was and worked with pp and they fixed that issue but after this update it stopped charging them all the way, I cant speak for a 36v...
  6. Replies
    13
    Views
    554

    Still only charging ionics to about 94% then goes...

    Still only charging ionics to about 94% then goes into standby
  7. Replies
    13
    Views
    554

    Pp charge update

    I recently updated my charge now if my ionics ar at like 85% it wont charge them I have it hooked up to a 2 12v trolling batteriesand 1 on starting and the trolling motor batteries go into standby...
  8. Replies
    4
    Views
    188

    Thanks

    Thanks
  9. Replies
    4
    Views
    188

    Another ? About exhaust tuner/mid

    Mercury pro xs 150 1b916729. I removed lower unit because I wanted to check for loose exhaust tuner good news. Its not loose but I have seen where people use a flashlight and look to the midsection...
  10. Replies
    3
    Views
    199

    Correction, I can get it to stop just had to turn...

    Correction, I can get it to stop just had to turn it a little more and hold it
  11. Replies
    3
    Views
    199

    Question on leak down

    Mercury 150 pro xs (1b916729) I know this isint the correct way but I got a leak down tester when I hook it up to cylinder 1,3,5 Say at 50 psi take a ratchet and turn the motor clockwise until ...
  12. Replies
    1
    Views
    224

    Checking reeds

    2012 Mercury pro xs 150 (1b916729) if I pull off the air handler/intake to check reeds will I need to replace gasket?
  13. Replies
    29
    Views
    931

    This has been going on for a few years have had...

    This has been going on for a few years have had it at multiple shops and of course they cant go out every day and keep running the boat its just random that it happens. I cant do the "required" test...
  14. Replies
    29
    Views
    931

    Went out sat. to fish a tournament and immediatly...

    Went out sat. to fish a tournament and immediatly the motor fouled #1 plug so now it just seems a random plug on either bank will foul maybe 5-10 minutes of idle time frim loading it up last time to...
  15. Replies
    29
    Views
    931

    Mine usually foul at wot

    Mine usually foul at wot
  16. Replies
    29
    Views
    931

    I dont believe my tuner has fell off, i dont hear...

    I dont believe my tuner has fell off, i dont hear any banging around, I had lower unit off a few months ago to change water pump not sure if you can tell if its loose or not that way bit i looked up...
  17. Replies
    29
    Views
    931

    Wouldnt a faulty map sensor throw a fault code

    Wouldnt a faulty map sensor throw a fault code
  18. Replies
    29
    Views
    931

    I have went through many plugs with this issue, i...

    I have went through many plugs with this issue, i can run wot shut off the motor and they are still black, it been an ongoing issue and apparently no shop can find an issue, sometime it will run fine...
  19. Replies
    29
    Views
    931

    Gap is set to .042

    Gap is set to .042
  20. Replies
    29
    Views
    931

    Also the shrader valve on the top of the rail...

    Also the shrader valve on the top of the rail which is fuel when i pressed it today fuel came out then it was like alot of air with some fuel is this normal, I dont have any fuel come out the shrader...
  21. Replies
    29
    Views
    931

    This is the fouled plug but all my plugs are dark...

    This is the fouled plug but all my plugs are dark like this, maybe getting weak spark im not sure
  22. Replies
    29
    Views
    931

    Would a faulty crank position sensor possibly be...

    Would a faulty crank position sensor possibly be causing week spark that ends up fouling eventually mainly at wot without an alarm or code
  23. Replies
    29
    Views
    931

    I only have vessel view mobile and it dont give...

    I only have vessel view mobile and it dont give me temp per bank just water temp, that was my thought aswell, i might change the thermostat anyways, but it was acted like it might have lost spark or...
  24. Replies
    29
    Views
    931

    Im just wondering why it would clear up then stop...

    Im just wondering why it would clear up then stop again, I had the injectors serviced about a year ago, almost acts like it might be loosing fuel to a random cylinder but keeps oiling, the plug is...
  25. Replies
    29
    Views
    931

    Random plug fouls 2,4,6

    1B916729 150 proxs keep randomly fouling a plug on just 1 side, thermostats have been changed water temp is 70 air temp in 80's boat ran fine yesterday but today had a sputter at wot then droped...
Results 1 to 25 of 149
Page 1 of 6 1 2 3 4