Deterioration may not have been the best word to use. Burned/overheat is the better description. That is absolutely burned heat shrink.
Looking back at my old pictures, I did myself a...
Type: Posts; User: Rubber_Duck
Deterioration may not have been the best word to use. Burned/overheat is the better description. That is absolutely burned heat shrink.
Looking back at my old pictures, I did myself a...
Thank you for the reply. Been a busy month, finally got time to look into it more last week. None of the flywheel magnets were dislodged or broken from what I could see. I did not remove the...
Model # :E225DHLSCF
Serial # :05221394
A month or so ago my 08 225 threw a code 17, and I found a chafed wire in the attached picture. It's the yellow wire coming off the stator. The actual...
I have 50s for the 36V ultrex on my boat. I do not regret not going to the bigger size, the 50s are more than sufficient for my use. One of the reasons I went with the 50s over the 100s was lack of...
Had a stored code 17, 55V circuit below range. Found a damaged wire coming off the stator that may be a cause for my problem. The stator resistance tested good. I don't have the equipment for the...
Thanks guys! I won't worry about that then. Now just to dig into that check engine code.
Model # :E225DHLSCF
Serial # :05221394
On my last trip out, I had a check engine light come on and the motor went into limp mode. It restarted fine and ran fine to the ramp. I'll find out what...
SJ is just a taper design, and MB is another. You don't have to build SJ blanks as a spinning rod. I'd recommend baitcasting for the SJ736 due to the power of the blank.
You shouldn't need the bill of sale for the boat you sold to get the new one licensed. You just need the documents for the new one.
Edit: I forgot about using that as a trade in to reduce your...
https://dor.mo.gov/motor-vehicle/watercraft/
Although we typically buy the boat/outboard/trailer package with a lump sum price, you still need to break out individual price of the boat, trailer,...
Thanks guys!
I recently splurged on batteries and realized during the install that the rings from the cables that come from my outboard are 5/16" while the battery studs are 3/8". Here's my question: Is using...
Which Columbia pants do you already have? I like the Columbia blood N guts pants that aren't the convertible ones.
My Stratos 200XL is about the same size as the Caymas you have on order, and I think you'll have enough boat. I also avoid the real busy weekends.
2017 CCSB Canyon with the 2.8L diesel towing a stratos 200XL
35-38 < 65 mph
30-33 > 70 mph
Unsure on city, somewhere in the 20s
16-22 towing
I can't say where the epa mpg numbers from my...
I like the Fuji LG tiptop for my bass rods as long as you don't need it in black.
I have one (hybrid F150) on order, so I'll have an answer after I get it early summer (hopefully). Not expecting earth shattering mpg or anything, especially compared to the diesel canyon it's...
I built my frog rod on the MHX MB874. All the MHX MB blanks I have handled have a soft tip and get into the backbone in a hurry. We don't have all that thick of vegetation around here, so you may...
Microwave guides are also an option for spinning, they'll accomplish the rapid reduction similar to the Fuju KR layout. That being said, I'm putting a KR concept guide train on the spinning rod I...
I never have. Highest I've seen is 5800 with an empty boat on a summer morning. And I was well into the 70s at that time.
I have a 27 tempest on mine. It was what was on it when I bought the boat, so I don't know what a prop shop could have done with it.
Ditto. I put a wire next to the thread carriage as a tension device and added a couple screw eyes to get the thread over to it. And those elastic hair ties work well to hold the blank in the rests.
I placed two orders of this year. First was a single blank that took 6 weeks. Second was four blanks that took 2-3 weeks. I was pleasantly surprised how quickly they shipped.
I take it you've already tried unplugging your modem/router for a couple mins and called your ISP for support?
It could be a bunch of things on your end or the ISP. Issues I've had include...
I build for myself. You can get a lot more rod for your buck as long as you're using nicer components. Plus you can make sure how the rod is set up is what's best for that specific blank and the...