Search:

I’m thinking king about modifying my ghost to use 2 lift shocks, side by side … with the turret and ffs it’s much heavier than normal

I’ve got one for ya Bill, if you’re interested. After adding a FF sonar on my ghost, the lift assist just isn’t as much help. I don’t see anyone making a booster for the Lowrance ghost, but it looks...

549165

New part came in, easy to replace, about 40 minutes start to finish and the part 40.00.
all LEDs working now

I’ve owned three different hydraulic plates, worst mistake I made was not buying the gauge. I’d always looked back to see my adjustments. I have one now and can put the plate exactly where I need it...

Trolling motor works great but the small blue LED for 24V has been out for a while. I’ve ordered the replacement board/part for it. Just curious if anyone has had to replace theirs??? Any advice ?...

:thumb up2:I know the Attwood anchor rein and anchor rein 2 came standard on rangers for a long time. Just seeing if anyone removed them or doesn’t use them. Happy to pay if you don’t mind shipping....

DFI suggested i use the 05 EMM and injectors(newer emm etc)
they will install mapping for 200HO. Compression is good on the 05. 120-125.
the 01-05 blocks are shared but I’ll stick with pros...

Fingers crossed , I found an 05 225. DFI says they can reflash computer to a 200 map. I was hoping I could just swap my EMM and injectors, but can’t verify that it would work. I thought BRP kept the...

Looks like a spark plug electrode came loose

They are shot sir. Looks like it happened before I got the motor. It’s been running for 4-5 years .

my low compression on the 01 E200FPLSIF RAM is due to a severely damaged #3 cylinder.

can I use a donor block from 01-05 200/225 and change over my ECM and Injectors???
I wasn’t sure if the...

https://www.dropbox.com/scl/fi/7cj4eja2mcyr1o44uih9c/IMG_0184.jpeg?rlkey=dtakuvq2ltl239phfe68bhevp&dl=0...

Put mine in from BFE last week. Definitely not a cheaply made product. By the looks of it, they had to source the replacement head cap from Lowrance, then a thick plexiglass cover to keep things...

Nope, no metal. That plug is more WET , no clue why. Motor ran great the day before maintenance. Head gasket is on the way, just don’t like digging in til I can finish what I start.(old man brain...

Did the Decarb yesterday, definitely dirty. Port side are all above 130. Starboard are 124, 85,120. Going to pull head and see if it may be the head gasket or …. Self explanatory .

E200FPLSIF 2001 Ram injection. Doing yearly maintenance and decided to do a compression test.
Cylinders 1,2,4,5,6 125-130

Cylinder #3 85psi

any chance I just need a head gasket?? Stuck ring?...

Perfect. Thank you sir

Does the new 3n1 HD transoms mount transducer have a temp sensor built in? Or do I need to get one for the nema 2000 ? Thanks

The ultrex bounce buster is located further off center. The ghost bounce buster sits right on top of the gunnel. I decided to move the ghost mount in further which meant a few new holes to drill.

I just installed my ghost and used a pc of shower pan(40 mil rubber) in between. Definitely miss the minn Kota shaft center positioner(????) looking at fabbing something up to keep the lower shaft...

just thought id ask here, part # 000-15882-001 , can't find one anywhere. any help much appreciated, thanks

im in need of the extension cable for the TMC-1 part # 000-15582-001 any help greatly appreciated .. thanks

Plexus. It’s pricey but works perfect. I usually get it off eBay

Sat in same boat for a few months, got a refund and bought the Ghost trolling motor and Active target