Search:

Type: Posts; User: Gambler05

Search: Search took 0.00 seconds; generated 45 minute(s) ago.

  1. Replies
    10
    Views
    321

    I agree Thumpin - would much rather fish 3...

    I agree Thumpin - would much rather fish 3 rivers.

    Thanks for the info Ranger482. They'll probably will call the inside harbor off limits.
    One nice thing is they usually drop the length limit,...
  2. Replies
    10
    Views
    445

    Fluke - Word of caution - if you've never been on...

    Fluke - Word of caution - if you've never been on Braidwood and you see a hazard buoy - stay clear. You can be traveling in 20' of water and next second 6" without a lower unit, I've seen it happen.
  3. Replies
    10
    Views
    321

    Heidecke Lake - Assitance

    This will be my second year coaching our high school IHSA bass fishing team. Last year was our inaugural year and we assumed we would be at LaSalle Lake. We were all excited since I used to fish this...
  4. Replies
    19
    Views
    1,602

    Nipper & Motomania are correct. I purchase mine...

    Nipper & Motomania are correct. I purchase mine from East Marine, who had the best price at the time.

    I however had my wonderful wife actuate the plunger, using the screwdriver method, while I...
  5. Replies
    1
    Views
    5,629

    Sticky: 3/29/13 – Mostly sunny with air temps low to mid...

    3/29/13 – Mostly sunny with air temps low to mid 50's. Light & variable NE wind. Water temp COLD 43-48 degrees. Fishing was unbelievably slow - zero bass - goose egg!!! We jigged and rigged points,...
  6. Replies
    11
    Views
    465

    fishthenation...

    fishthenation, don't know if you took your boat in or not but my issue, also noted above, wasn't caused from an ignition coil. I was reading an other thread that Don was involved in and my symptoms...
  7. Replies
    11
    Views
    465

    Tom, I didn't experience sporadic behavior...

    Tom,

    I didn't experience sporadic behavior like yours but I was on the Miss river Saturday and after my third stop, same engine as yours except 2006, was hard to start and once started could...
  8. Replies
    20
    Views
    1,146

    Hey T.O. - Just remember if your wiring harness...

    Hey T.O. - Just remember if your wiring harness was corroded and you replace it with a similar plug it could happen again. If it were my boat I would solder, shrink tube wrap the connections and...
  9. Replies
    3
    Views
    494

    Thanks for the tip Al. I think I'll have to get a...

    Thanks for the tip Al. I think I'll have to get a ring from Mark.
  10. Replies
    3
    Views
    494

    Question for Blowout Problem

    I have a 2005 2100 with 225 Pro XS 6." Bob's with 2." spacer, height typically set at 3.", 27P Trophy Plus. I fish the Miss river often and occasionally get weeds wrapped around prop. When this...
  11. Replies
    10
    Views
    1,231

    Bob - after I posted last night I looked again on...

    Bob - after I posted last night I looked again on Transducer shield and inserted foot in mouth. I see they do have the LSS2 mount, as you pictured above. I also see they are proud of their products,...
  12. Replies
    20
    Views
    1,146

    The bilge pumps in my 2100 are located under the...

    The bilge pumps in my 2100 are located under the console between the seats, in the same area where my thru hull transducers are located. My manual switch has never failed but I've had to replace the...
  13. Replies
    10
    Views
    1,231

    Bob - I live out by Hennepin, close to the IL...

    Bob - I live out by Hennepin, close to the IL river. My parents live on the Iowa side near Prairie DC but that wasn't me out there. I do love that pool and the Lansing pool as well and fish them both...
  14. Replies
    10
    Views
    1,231

    Barry - did you mount direct or break away. I...

    Barry - did you mount direct or break away. I have been known to roll off of some Miss. river stumps and don't want to damage a $250 transducer.

    TRS - No my Bob's doesn't have the water block off...
  15. Replies
    10
    Views
    1,231

    LSS2 Transducer Mounting Tips

    I'm new to posting on the BBC but have read some good stuff here.

    I just upgraded my electronics on my '05 2100DC, from LCX25c to a HDS8 Gen2. Has anybody got any good mounting tips for that...
Results 1 to 15 of 15