What is a fair price to pay for a Minn Kota Maxxim 80lb thrust with built in transducer?
Type: Posts; User: Skeeter J
What is a fair price to pay for a Minn Kota Maxxim 80lb thrust with built in transducer?
I have a friend that's on the water this morning and called me saying that when he has the main power on, his motor will trim down and will not shut off. He can move it up then kill the power enough...
Thanks. I think I found it but not sure. I took off the cowling and lifted the rear lid. When I pumped up the ball, I could hear air and see gas seeping from that clear filter compartment so I am...
This may need to be on the Yamaha page but while fishing this past weekend I was getting a slight gas smell that would come and go. I'm assuming I have a leak somewhere but I took the cowling off...
Has anyone had success with this update? I was about to install it but a Lowrance rep at a fishing expo yesterday told me he was being told that it didn't work.
Wilcox bait and tackle on Jefferson Ave in Npt News does a good job matching up the eyes no matter how far down the rod they are.
This shot was without the motor running. It gets a little worse with the motor running and even worse still when I put it in gear and move.
Thanks for the responses. Hopefully one of the solutions will work for me.
Why am I getting the "noise" or "distortion" down the center line.? I've seen other images in here that are so much cleaner. Transducer is mounted just below and to the inside of the jack plate. ...
Yes. I've already gone to the marine dealer that installed them. I will be taking it back to them to take those things off and get the scratches cleaned up. Back to plain ol carpet for me.
http://www.bbcboards.net/attachment.php?attachmentid=279110&stc=1http://www.bbcboards.net/attachment.php?attachmentid=279111&stc=1
Just wanted to post a pic of the slick bunks for the guy that asked what they were.
Thanks...that could indeed be the problem. I fish in Southeast VA and it is mainly brackish water. It could indeed be coming from the low salt content in much of the water here.
I have slick bunks on my trailer and I noticed scratches on the bottom of my boat. I wasn't told of this possibility when I had them put on. I need some advice because I'm on the verge of have a...
Actually it does start at zero. It always idled between 5 and 10 but I haven't noticed it hovering at 30 when running. The water stream is good and strong.....just concerned at the pressure being too...
I could be me not paying attention, but I noticed on my last two trips that my water pressure gauge is topping out at 30 when running on plane. It hovers at about 8lbs when at idle. I could've been...
I have a 175 hpdi and I somehow managed to break the bolt or screw that holds the single wire that comes up from the lower unit and connects in the trim assembly area. Is this something that's easy...
Just wanted to thank the guys that responded to this post. We found grass on Friday and stayed in it all day during the tournament Saturday to bang out a respectable limit. Thanks again.
I have had a few episodes where the motor "clicks" when trying to start. When I moved the throttle lever back and forth several times, it eventually cranks. Is this a throttle position sensor...
Not a fan of the "bent pole" pattern, but I have seen it in full affect over the years...I only really get on the river a couple times a year, so thanks for the comments guys.
I keep hearing there's hardly any grass on the river this year outside of Aquia. I've always had grass to throw at and now I don't know how to catch a fish up there. Can anybody give me any...
What's the diameter of the bungee rod straps on the front deck and where can it be bought. Been to Lowes and Home Depot and didn't find anything close.
thanks. I'll take a look and see if that may be the problem.
I noticed that my trim guage is malfunctioning. The needle never goes lower than 3/4 when I trim it down as far as it will go. Am I facing replacing the guage or the sensor?? How big if a job am I...
I have an "under the passenger seat" cooler and I found some 1/4 inch styrafoam at the art supply shop. I cut it to fight tight inside the cooler and cut out the hole for the drain. It now holds...