Search:

I’m going to try and find out. Putting in a shielded wire harness(not commercially produced) that has its own ground, so I doubt my wiring will have an issue. That being said, you never know.

Thanks and will try again today!

Simple question for the group, have an '08 z520- is it possible to run a wiring harness thru the tube on the port side(trolling motor wiring tube)?

Tried to route a fish tape from both the bow...

The set of pads I have on the shelf may have been a Cavalier, can't remember. Will take the part number and verify at Autozone this afternoon.

Open question- Did they ever determine if this year...

Thanks Blair, looks right. Wished they had the Vortex hub included in their kit on the trailer parts website.

Looking for a part number on the right side caliper for a 2008 z520 trailer. Had my 4th hub in 4 years, come apart yesterday and it broke a corner of the caliper where the pad attaches. There used to...

2019 Laramie 4x4 with 29k miles, yes I keep the tires hot. If you're in the market, take an unbiased opinion of brand and drive one. There is not a nicer vehicle in a 4x4 truck on the market IMO....

Second Ram in 6 years- this one is a 2019 Laramie 4x4 with a 3.21, average 20.5 to 22 on the Highway and 18.5-19.5 driving back and forth to work. Work mileage is 75% highway so that number is...

Bob- thats the same software version that was loaded on it when I sent it in. Hope that problem is corrected with the service.

Chris

3.30

Solix conclusion- Humminbird shipped a replacement transducer and unfortunately it didn't correct the issue. We came to the conclusion to send the head unit, transducer back for repair which I did on...

Transducer is snug and all connections are tight. That was my 1st guess but checked the transducer when we put it on the trailer. Will be a couple weeks before I can get back on the water. will try...

Installed a Solix 10 in August and has worked normally until now. Operating a single transducer- while idling I'm seeing an erroneous depth(approximately 50-500ft), the SI and DI views are available...

Mark at Tennessee Valley Marine in Athens.

We are still messing with it. It worked perfectly on the hose and as soon as it was backed into the water, same problem. Educated guess is an intermittent issue with the switch but my mechanic is...

Shift position switch and shift cable are the culprits. It's less than 2 MM from being perfect but that's enough to cause the issue.

Will do

Need a little help, '08 HPDI Series 2 just completed the 100hr service. The motor starts and runs fine until you shift back into neutral from either fwd or reverse. About 75% of the time when shifted...

Comfort Inn off of the HWY 67/Belt line Exit(334) is fairly new and within a couple hundred yards of I-65. JW steakhouse is on the east side of I-65, at that exit, and the food isn't bad. If you want...

back lash....Fury 3 blade.

Have utilized two props (25T1 and a 26P Fury) for my 2008 z520, which is equipped with 1 PP, 10"Atlas and a 250 HPDI Series 2. I prefer the 26 Fury, which lifts my boat very well and will run low...

Had to cut hay, wasn't any cash left for handshakes. Tide faithful used it all up.

7 dust will kill them. After sunset, I normally sprinkle the 7 dust powder all over the ground, on the nest, and that takes care of the problem.

Same here with Harbor freight wheel jacks on just the 2 front axles for my z520. Most important part is to make dang sure that you backed it deep enough into the garage that your dolly wheels are...

+1

Have owned both and wouldn't own another Z20 due to the ride.