Price on A 8” please
Type: Posts; User: valeroman
Price on A 8” please
what size pistons are needed to rebuild.
I can,t read the serial number due to corrosion. Motor rolls on starter, fires and stalls. If I plug the air intake on compressor pump, it will run for a few seconds. If i retrict the fuel return...
Fixed!!!!! Loose black wire in coil - main harness connector. Thanks Don.
Load test is good. Found 2 faults . est 1 and est 4 shorted?? Unplugged these cdms and faults went away. Ignition fuse shows 12.8 when turned on then when relay clicks off , the voltage goes away....
Hello, the serial number is 0T443645 I am connected with a six foot remote that has a key and horn. Lester
I tested spark on the bench , than installed on midsection. Tested motor on stand, no spark anymore???? Fuel pump runs when key turned on, I primed oil pump with DDT but now I have no spark at all. ...
Customer lost 2006 150 opti ignition key serial #1B243317 on center console. Key switch has a tag saying 87-892336A01 How to I figure out what key number is?????
Hello Don, It looked like it shrunk between the poppit and the the brass hose fittings. Maybe the four bolts were not tight enough. The gasket was all bowed in the center wher the water flows.
Finally fixed !!!!!!!!!! First poppet cork gasket was out of place . Installed new gasket and block pressure increased to 4 lbs at idle. Once warmed up, it was still warmer on the port side, so...
Thanks, I will try that tonight. I am ready to junk this thing.
hello don, yes i use a infrared handheld gun aimed at the thermostat housing and starboard runs 143-145 and port shows 160 -up to 190 depending how hard i run motor. The head is so hot I can't touch...
Ran it again with a stock lower unit ,deep in the water and it ran at 180-190 again. Is the drain hole in the port cylinders which i see at 5 oclock in the water jacket , the only drain hole? We...
Don, i replaced all three gaskets and base. This case has a land n sea nosecone with one hose on the port side . |All fitting are tight on hose fittings I am going to run it with a different lower...
Customer ran boat last night. Temp 160 at half speed and 10 lbs pressure. At WOT temp quickly went up to 190 and water pressure stayed at 10 lbs. Don, I blew out all passages in adapter plate,in...
Water pressure at idle is 5 lbs and if you give the motor a quick rev it goes to 20+ pounds and then pees a lot of water. I do not know WOT pressure.
Serial # 0A927122
1988 200 hp merc with older 7 petal front overheats at idle ,cools at midrange and overheats at topend on the port side only. We changed head gaskets,even the heads, new thermostats, midsection...
Rebiuilt an 25" mercury 175 lower and changed it to a 20" driveshaft. Replaced exhaust hub and installed new pump with a new lower and all gaskets plus new shift shaft seal. Pressure tested to 15...
Thanks Don !
150 merc xri spewing unburnt fuel from prop. Checked all cylinders with timing light and 3 and 5 showed a steady light from timing light (no Pulses in light). I put a new switch box in for...
Hi Don, i have a 2008 250 pro xs in my shop with a turned sleeve in number six with no compression on 6. I had a new sleeve put in #5 last year and now this. The owners would love to sell with or...
Hello Don, Its Lester from Hanley Marine in Nova Scotia, I have a 2005 300x that only turns 6200 with a 25, 26, 27 tempest and a tried a 30 chopper and again 6200 rpm. Does this have a limiter when...
We found a faulty battery switch on the possitive cable. This helped with the trim switch power increase
but now the motor is surging at wide open. We are going to check the final filter in the...
We found a faulty battery switch on the possitive cable. This helped with the trim switch power increase
but now the motor is surging at wide open. We are going to check the final filter in the...