Search:

Type: Posts; User: svtlightning93

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    173

    I have the motor tore completely down due to #5...

    I have the motor tore completely down due to #5 cyl ran lean. I used a 3bolt puller with point on jack bolt which caused the flaring. The edges have split and chips cracking away. Only choice i have...
  2. Replies
    6
    Views
    173

    250 proxs flywheel nut size

    2009 250 pro xs 1B764545

    flared out crankshaft threads removing flywheel, what size are the threads? Only thing i can find is M16 and want to make sure to get the right die
    thanks
  3. I cover mine in case a hydraulic line leaks while...

    I cover mine in case a hydraulic line leaks while traveling so it doesn’t allow pole to lower and drag the road, a simple strap would do the same.
  4. I miss Louisiana hot and humid weather compared...

    I miss Louisiana hot and humid weather compared to working in Saudi Arabia. Actual temp is 119 and humidity is high. Heat index is in the 150’s, just stand around and b/s for a little while and look...
  5. Replies
    33
    Views
    1,843

    Was 146* heat index in saudi the other day,...

    Was 146* heat index in saudi the other day, Brutal working in this heat on a drilling rig. Deck temp is 170*
  6. Replies
    34
    Views
    2,489

    I have an odyssey 2150 as my cranking battery,...

    I have an odyssey 2150 as my cranking battery, run 2 hds 12’s, livewells and never got close to draining it. That battery is a beast.
  7. Replies
    10
    Views
    914

    I launched a16’ flat bottom in my pond for years...

    I launched a16’ flat bottom in my pond for years with a Polaris 900 ranger. It was a fairly steep ramp and it slid sometimes, I would never attempt to launch a bass boat with utv, it doesn’t weigh...
  8. Replies
    4
    Views
    409

    What rpm’s are you running top end with the 26?

    What rpm’s are you running top end with the 26?
  9. Replies
    11
    Views
    631

    I have the general Altimax’s that came on my boat...

    I have the general Altimax’s that came on my boat new since 2015, zero problems so far, been very good tires.
  10. Replies
    4
    Views
    409

    Tempest plus

    Anybody running a tempest plus on their z520. I’m tuning 25 fury3 and run about 68 tops most of the time. just curious if the tempest would be a little faster.
  11. i would say so, lol. Most of the time it’s...

    i would say so, lol. Most of the time it’s operator error that shreds a belt. Usually in high gear and putting the bike in a strain, when it should have been in low. Some bikes will eat belts due to...
  12. Replies
    34
    Views
    1,560

    Might blow out a seal, but don’t believe it will...

    Might blow out a seal, but don’t believe it will overheat the bearing, never heard that before
  13. Replies
    10
    Views
    427

    My pest control guy has a battery operated...

    My pest control guy has a battery operated backpack sprayer that’s rechargeable and he loved it. Not sure what brand though. I be always used the echo sprayer with decent results, I always rinse it...
  14. Replies
    2
    Views
    477

    Just got back from 4 days on Bruin, fishing was...

    Just got back from 4 days on Bruin, fishing was tough. Caught a few shallow on the bank but most off the shady side of piers when sun was out. Lipless crankbait and crankbait worked for me. Shad are...
  15. I don’t believe so, I haven’t found out how on my...

    I don’t believe so, I haven’t found out how on my z520c. Pull out the red nozzle and water directs from stbd to overboard but keeps flowing in the port livewell. Would be nice to direct all flow...
  16. Replies
    11
    Views
    540

    Blue sea has a good marine fuse block. I believe...

    Blue sea has a good marine fuse block. I believe 10 ga 12v dc is rated for 20 amps up to 15’ then is starts dropping, so you should need a 20a fuse block. I would run 10 ga wire to the fuse block...
  17. Thread: Gnats!!

    by svtlightning93
    Replies
    39
    Views
    2,795

    Anything that has vanilla extract in it. You...

    Anything that has vanilla extract in it. You gonna laugh, but Victoria secret amber romance works very well, vanilla extract and water concoction works too.
  18. Replies
    20
    Views
    993

    I like my lithium bubba blade, the handle is a...

    I like my lithium bubba blade, the handle is a little big but does a good job.
  19. My incision got infected and was either a hair or...

    My incision got infected and was either a hair or piece of stitch, after about 6 days I had enough and just squeezed the hell out of it and stitch shot out, day after that I was good to go.
  20. Replies
    9
    Views
    980

    My 2015 z520c came with general altimax, rated...

    My 2015 z520c came with general altimax, rated for 75,000 mile treadwear. They have been good to me, not 1 issue.
  21. Replies
    15
    Views
    1,123

    Cerakote has to be baked to cure, lowest temp is...

    Cerakote has to be baked to cure, lowest temp is about 2hrs at 200 deg , not sure what the melting temp is on the side panels. I prepped and sprayed mine with paint specifically for plastic and is...
  22. Replies
    15
    Views
    1,123

    Not trying to preserve the vinyl, cleaning and...

    Not trying to preserve the vinyl, cleaning and scuffing the material so the paint will adhere to it. I tried every product including back to black, barely made a difference on mine so I painted them.
  23. Replies
    15
    Views
    1,123

    I tried everything on my 2015 due to them almost...

    I tried everything on my 2015 due to them almost looking gray. I took mine off, scrubbed them with rubbing alcohol and scotchbrite pad, sprayed with bulldog adhesion promoter and then krylon matte...
  24. Replies
    15
    Views
    1,087

    Make sure put some oil on the threads before...

    Make sure put some oil on the threads before installing the nut if the nut and bolt are stainless steel. It will seize up and you will have to cut the bolt off.
  25. Replies
    19
    Views
    1,971

    I tried that razor and i got ate up, I tried...

    I tried that razor and i got ate up, I tried different shaving creams and still same result, went back to my mach3.
Results 1 to 25 of 311
Page 1 of 13 1 2 3 4