Search:

Type: Posts; User: mikesxpress

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Rivnut is installed into the base material and...

    Rivnut is installed into the base material and the panel is attached with the fasteners.

    https://m.youtube.com/watch?v=dkPhGIaPCVs
  2. Is it glued on?

    Is it glued on?
  3. Replies
    26
    Views
    1,795

    Robert, no I don't. The stock pump continues to...

    Robert, no I don't. The stock pump continues to run after pumping. I have made corrections to the field affect switching to eliminate that issue on my pump but wouldn't want others to do it.
  4. Thread: Brake drag

    by mikesxpress
    Replies
    12
    Views
    181

    Two new calipers, new pads, lube pins, and...

    Two new calipers, new pads, lube pins, and flush/bleed the fluid. Then your go to go for awhile.
  5. Replies
    18
    Views
    851

    James, Lanier rocks 6 footers from the ya'hooer...

    James, Lanier rocks 6 footers from the ya'hooer boat traffic all summer. But the fish school up in the wash if you can stay in the boat to fish them. That traffic there has monster tubs with the big...
  6. The other new TM's I reviewed at ICAST all have...

    The other new TM's I reviewed at ICAST all have freshwater only limitations. The MG does not so that is a driving factor for me as I fish tidal waters. The head and mounting bracket on these MG's is...
  7. Rick that was me. I moved that turd out of the...

    Rick that was me. I moved that turd out of the boat years ago and helped some local guys do there's too.
    I sent the design to the charger OEM and they "said" it was a sound modification and would...
  8. Replies
    5
    Views
    400

    I would be interested to see if the cracks from...

    I would be interested to see if the cracks from these saltine cracker fenders transmit thru the sprayed on bedliner material? The fenders are going to continue to crack but this may slow it down?
  9. This is not a Band-aide repair. 10-32 UNF...

    This is not a Band-aide repair.

    10-32 UNF aluminum Rivnuts with a stainless washer backer. Now you have easy on/off fasteners you never need to mess with again. Just snug the bolts with a nylon...
  10. Replies
    11
    Views
    213

    I had Ford diesel trucks until the low sulphur...

    I had Ford diesel trucks until the low sulphur fuel was imposed and it no longer became financially a sound decision as the diesel fuel was allot more expensive. Add the DEF additive and that was...
  11. Thread: Brake drag

    by mikesxpress
    Replies
    12
    Views
    181

    As Jeff noted they all drag a bit. Ensure the...

    As Jeff noted they all drag a bit. Ensure the areas for the caliper/pad pin is clean and lubricated and the pad piston itself is not corroded or hanging up.
  12. Replies
    1
    Views
    74

    That was Rangers design on the older boats to use...

    That was Rangers design on the older boats to use the center bunks as primary support. While this makes loading easier it doesn't adequately support the hull while trailering. If you replace the...
  13. Replies
    8
    Views
    597

    https://www.venturetrailers.com/buying-guide/how-t...

    https://www.venturetrailers.com/buying-guide/how-to-choose-a-trailer/
  14. Replies
    12
    Views
    222

    Wes it doesn't look like you have done any...

    Wes it doesn't look like you have done any reparations to your livewell system before? If the plumbing hasn't been cleaned out, flapper valve rebuilt/replaced, or any pumps replaced, it most likely...
  15. Replies
    10
    Views
    396

    Big difference between electrolysis and saltwater...

    Big difference between electrolysis and saltwater corrosion.
  16. Replies
    3
    Views
    136

    Aftermarket aluminum trailer is a good option....

    Aftermarket aluminum trailer is a good option. They can be built to match your hull.

    https://www.venturetrailers.com/buying-guide/how-to-choose-a-trailer/
  17. Ted AC put three X2's in that area without...

    Ted AC put three X2's in that area without modifications of the pultrusion? I want to see that.
  18. Not going to get three group 31's in the port...

    Not going to get three group 31's in the port side on mine. Too small.
    https://imgur.com/ebmgrBv
  19. Replies
    8
    Views
    597

    If your at the trailer replacement point you may...

    If your at the trailer replacement point you may want to consider an all aluminum aftermarket trailer vs another steel one. Quite a few reputable on-line choices that will either build or be capable...
  20. Replies
    6
    Views
    425

    Jeremy is spot on. Go to BPS and compare the mid...

    Jeremy is spot on. Go to BPS and compare the mid range units that will do what YOU want them to do. Then go shop pricing.

    Depth, water temperature, structure visibility via 2D, decent map chip,...
  21. Replies
    8
    Views
    466

    :laugh: Yep. I'm waiting for the video of how...

    :laugh:
    Yep. I'm waiting for the video of how that works out....
  22. Replies
    64
    Views
    2,138

    Many folks with a Flow-Right remote drain plug...

    Many folks with a Flow-Right remote drain plug open it at the ramp after loading up for a quick drain and then close it for the trip home. The grease applied to the O ring area will attract road crud...
  23. Replies
    4
    Views
    187

    As your into pump replacement mode you may want...

    As your into pump replacement mode you may want to review this:
    http://www.bbcboards.net/showthread.php?t=952123
  24. Replies
    89
    Views
    6,116

    If that's installed just to get it to the glass...

    If that's installed just to get it to the glass shop it's ok. If your intention is to use the boat with that it's not ok.
  25. Replies
    21
    Views
    976

    No issue with my 23P 3 blade Fury all holes...

    No issue with my 23P 3 blade Fury all holes plugged, JP all the way up, and trim all the way up on a Z21Ranger.

    https://youtu.be/OE_OSw442zA
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4