I did the choke mod on mine a long time ago. I really dont have any con's with the mod I find that I get easier starts during the summer because the ecu is not enriching the mix. I believe with the...
Type: Posts; User: tomcat
I did the choke mod on mine a long time ago. I really dont have any con's with the mod I find that I get easier starts during the summer because the ecu is not enriching the mix. I believe with the...
I had Jay Smith do mine out of Texas couldn't be happier with the results. He's been doing them for a long time.
Jay Smith Race Engines 832 597 2603
Email hitman6563@yahoo.com
When I had access to it I used the 5606 aircraft hyd fluid. I had to repair the bleeders about 3 or 4 years ago ,I flushed and refilled using ISO 32 hyd fluid from napa. Been problem free so far no...
I hava a 98 dc2000 cb on the front panel a 2 o3 3 fuses in the bilge area on the main lines going front
J
The back of the case does feel hot but not sure if it just from it being black and in the sun. It mounted on a ram mount I did ask that ? and the tech said it should work fine all the way up to 160...
Got a call back from HB yesterday said they couldn't find anything wrong with the unit. They did tell me it comes with a 90 warranty if it acts up again. Hopefully it'll straighten out unit only has...
I have a 1998 astro 2000 dc I believe it just about a twin to the 205. Mine does have a 44 gal tank and I'm running a 200hp efi merc with a 6 inch plate. I had a 10 on it but did not like the way it...
I've ran Penzoil prem plus and xlf for a long time on my 98 200 efi pre mix 40-1. Even before I had my eng rebuilt by Jay Smith Racing, he recommended it. My rebuild was for a timing issue not oil...
I have the same eng 1998 200efi I deleted my oil inj and premix when I got the boat in 2001 just for my peace of mind or whats left of it
J
I've had the merc scoops on my 200 for a long time no problems so far
J
Helix 5 DI GPS lake card for Illinois region latest software installed.Its on it way to humminbird hopefully to be fixed but thought I would post my problems here for any feedback. Main problem...
On my 1998 200 efi i had a split in the vacume line on the fuel pres regulator. In rougher water motor running about 40 get bounced hard and motor would fall on its face. Took a little while to...
Thats what it was on my 1998 200 efi I replaced the o rings on the relief screw. Don't know if there the same are not but I picked up the o rings at lowes Danco brand #5 #36 and #60. Another thing to...
I have ran both but mostly pennzoil prem plus and xlf since around 2002. Even though I just had my eng overhauled for a melted piston crown from a timing issue everything else was fine. This is on my...
Had trouble with my eng a year and a half ago after a rering 1998 200efi. Motor went down on power #2 low compression. Had found a great big mouse nest and figured it had gotton some sucked up in the...
Thanks Don
Don I tried to PM you but If you get this twice plus here I apologize computer is fighting me.
Engine Mods
Heads cut by Jay Smith, TDR reeds, Oil Injection removed and Detonation cont box removed....
Another thing to check is the vacume line on the fuel pressure regulator. Mine got a small split in it one time and would act up in rough water
Your just splicing two wires together butt splice and some heat shrink or elec tape. I soldered mine together then some heat shrink.
Justin
Unplug the bullet connector for the trim sending unit. Turn the ign on and see if the trim indicator pegs to one side or the other you can also take the trim wire that goes to the indicator and...
No problem I hope this helps.
Justin
I fought this on my 98 200 efi would start fine in the morning as the heat and humidity got sky high it would just pop once and kick out the starter over and over crack open the throttle and...
With out looking at a wiring diagram my guess is its how it reverses polarity to the trim motor . Had similar setups on the jets I worked on.
I got about 8 miles of the Illinois river memorized right now a little mind numbing after a while
Update
I've been slowly breaking in the new rings. Got just about 10 hours on it so far been gradually working up to higher rpm runs. Gotten back the low/mid range torque. With the oiler removed...