I have Helix,ML with newest updates and Ultrex I-pilot link.I had seen mentioned a problem not being able to Delete WPs that are created when you hit Spot Lock. Has there been a way figured out yet...
Type: Posts; User: RonH54
I have Helix,ML with newest updates and Ultrex I-pilot link.I had seen mentioned a problem not being able to Delete WPs that are created when you hit Spot Lock. Has there been a way figured out yet...
Don't think there is but wish there was. Like you I can do most by memory but the resetting is the thing I dread most about doing updstes.
Ok. Thanks for that info. So if I go 1 click up I need to use Auto setting?
I am pretty sure I did but who knows. I usually on 30-40 but really thought I had a 10 option at one time. So 1 click up from "Down" is 20 degrees? I thought each Click was 10 degrees from 10-60.
Just updated my Helixs and ML(1.3) everything went smoothly and so far Great picture. But I do Manual setting and when I go to Forward Mode and start scrolling to set degrees Forward it goes from 20...
Thanks Wayne. I had read the 1.29 exposed the Hardware problem so I figured everything will be fine with newest update. Just wondering if anything odd/new has happened to anyone with the new 1.3.
My setup: Networked Helix12MDI G2N,Helix12MDI G4N,Helix10MSI G4N,Ultrex i-pilot link and ML all thru Network Ports. When I went to 1.29 on ML I got the TM interference and HB replaced the ML and...
My bad on wording. Thanks for the info
Since the Ultrex 36v I-pilot link can pull up to 56 amps( I think that correct) whenever I need to replace my AGMs I will need Lithium Batteries over 50 amps each, correct? I have guys say they have...
Thanks Wayne I figured you knew abswer
I didn't purchase in a way. Back in '22 my Helix 10 MSI G2N went out. I sent to HB for repair and they just replaced it with a G4N at whatever cost I sent them for the repair
I done all updates before using SD Card on my Birds and Garmins before. Never had any problems with updating but will have to go to my boat at my Slip to get S.N.
I doubt this is it but could it be different model Transducers(older) came with different ones based on S.N.?
Not sure I do the update to my Helix and ML yet because everything doing Great at the moment but this is interesting. I have a Helix 10 MSI G4N, there are 2 different updates based if your Serial #...
Everything going great but I got a question just for input from you guys. My Setup: Networked Helix 12 G4N MDI and Helix 12 G2N MDI at Bow, Helix 10 G4N MSI at Console, ML and Ultrex 36v I-pilot Link...
My Setup,Port switch with Helix12 G4N and Helix 12 G2N at Bow, Helix 10 G4N at Console with ML also in Network. Both the G4N s and the ML have newest update and been fishing about 6 times with this...
Sent mine back 2 weeks ago and got new one with Manufacture date of 9-2-23 and all my RFI from Ultrex link was gone.
Thanks. I love to read Technical articles like that
Same here. Fished 8 hour yesterday after getting new ML from HB. The Clarity and Tracking now is Amazing and IMO matches Garmin LV34.
My bad. I will edit. Typed wrong
The one I got in March of 2020 had theses as 1st 6 # 220202. The one I got from HB as a Warranty replacement in June of this year had these as First # 230314. So I assume my dates are 2/2/22 and...
Yes. I called Monday,they sent me my RMA sheet and Mailing label and I dropped off at UPS Monday. They got it Wednesday and sent new unit out Wed. I am in SE Ky. about 8 hours from Eufala.
Got to figure that the case. I figure the one they sent me as an replacement in June was one they just grabbed at their warehouse. My newest one on UPS truck and be here tomorrow. Will put on...
I had my first ML that I purchased in March 2022. I got cracks in its cable and HB send me a new ML in June of this year. I then got the TM interference after the update on the one I got in June. So...
Good question. I just returned my ML to HB and they sending me another one. I had the interference on my Helix 12 MDI GN4 from my Ultrex 36v I-pilot link