Still available? Info would be helpful. Interested in a 52S or 52M.
thanx
Type: Posts; User: yukonjack2
Still available? Info would be helpful. Interested in a 52S or 52M.
thanx
https://www.amazon.com/Deutsch-3-pin-Pigtail-14AWG-Copper/dp/B07FT2RCC1/ref=pd_rhf_ee_s_rp_c_0_22?_encoding=UTF8&pd_rd_i=B07FT2RCC1&pd_rd_r=3cc5df4e-4171-4fba-b1a5-17e07aebe4b6&pd_rd_w=8uwic&pd_rd_wg=...
A Little Late to the game, but Deutch connectors are used in Marine applications all the time. I went with 3 Pin to be able to run the alarm wire as well.
...
Can i drip in a replacement 175 ppwerhead? Is exhaust line u
I may have blown my powerhead last night - waiting ont he bad news from the shop.
My question is - if I hav eto replace it, can I upgrade at this time to a 175 efi and keep the rest of the...
I am running 20 lb smackdown - really like it for dropshotting.
2005 Nitro 882, 2005 mercury 150 Xr6
Full Tank, empty livewells, tourney load, 2 guys
23 tempest plus
5400 RPM, 58.5 Mph
16-18 psi WP
bobs 6" plate - holeshot 4.5" below pad very fast...
Caught a few Today on the US side from Grosse point down. they were shallow - 5-6 ft, and scattered. 1 here and 1 there. Lots of white bass and a big pike to round out the day.
Water was ...
Ill take it locally if deal falls through.
we can deal if you decide you don't install them.
Ditto - albeit I ran 16 ga wire from the fuse block to the power cords of my helix 9 and 10.
sometimes the obvious is not obvious. I had the motor on the top hole - I had it raised up 2 holes, and now it doesn't hit at bottom of the jackplate travel.
Mike:
what do you think of a back up 4 blade ot the 23 tempest plus?
I think(you know how dangerous that is) going up in pitch 1 inch to a 24 trophy plus, or better yet fury 4 would aid the ass...
all is good - sometimes the obvious isnt so obvious. instead of moving back to avoid the steering cylinder, going to move the motor mounting holes up on the plate, this way at full down it won't...
I got a screaming deal on a 6" bobs jackplate, and replaced the current fixed slidemaster setback plate with it. I then added hydraulic steering as I had the infamous corroded steering cables. ...
I got a screaming deal on a 6" bobs jackplate, and replaced the current fixed slidemaster setback plate with it. I then added hydraulic steering as I had the infamous corroded steering cables. My...
TRy pulling the motor cover and check the wire connection. It is tucked in on the lower starboard side. Mine hade just came unplugged. there is one for up, and one for down -
blue wire and a...
do they make a dual gage for each block temp readings, preferably in a2" gage size?
If you can find any info on the sensors, It would be greatly appreciated.
I checked it out today, and there appears to be a sensor on each bank just below the upper spark plug. there is a brown with blue stripe wire coming from each one. Can I tap into these wires on...
fyi - there is a slot in the shaft for your ducer cable. you have to pull the head off, pull the shaft out, and silicone it in all the up the length of the shaft through the motor, and
then zip tie...
After reading up on the cold seize and hot seize issues, as well as proper warm up and shut down procedures, what is required to easily install a temp gage somewhere on the dash to connect to my...
I have an 882, but following. Installed the 52 ultrex and it is big. footpedal fit is not even close, so I need a plate as shown, or cut the deck and intall an aftermarket footwell.
comfort troll,...
thanx Don.
When you have time, electrical issues abound in a few years installation. It is highly reccomended to run power for your graphs directly to the battery. I put a 6 circuit automotive type fuse...