Search:

Type: Posts; User: Podcast

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    307

    Triton Boat Lid Latch/Lock

    Looking to find a site that sells the metal lids locks. Not a fan of the old plastic ones, I can easily pull them open when they are in the lock position.

    Thanks.
  2. Replies
    1
    Views
    200

    Could be many things. My experience is one of...

    Could be many things. My experience is one of two things though. First, fuel filters, especially the high pressure pump filter. Second, I had an issue with the spark plug wire "caps". One wire...
  3. Replies
    2
    Views
    131

    I wouldn't recommend a 10" JP on any 18' boat. ...

    I wouldn't recommend a 10" JP on any 18' boat. Remove the spacer and you should be good. You'll need to play with the plate a bit. I've never run that motor on my 18 so I couldn't say. What...
  4. I agree with the consensus. Trim down. I don't...

    I agree with the consensus. Trim down. I don't get it much with mine but I have boat to leverage out of the water so my prop does not work as hard to keep me on plane regardless of my load.

    I...
  5. Replies
    1
    Views
    109

    Nevermind. Helm holes lines up to trim switches....

    Nevermind. Helm holes lines up to trim switches. All good and installed.
  6. Replies
    1
    Views
    109

    Installing Blinker Trim, Help

    I've got a dual blinker trim I'm installing onto my hydraulic steering. From what I have researched the process is to drill set screws into the helm casing. Can anyone confirm this? This sounds...
  7. Thread: Trailer

    by Podcast
    Replies
    4
    Views
    345

    Trailer

    Where's the best place to find/purchase a replacement trailer? Mines seen better days but the boat is in great condition. Been looking for awhile but hard to find. Thanks.
  8. Replies
    18
    Views
    502

    Thanks for the responses. They definitely do...

    Thanks for the responses. They definitely do advertise these supporting LiPo. Main description says this: Supported Battery Types: 12v AGM, 12v Flooded Lead Acid, 12v Lithium LiFePO4
  9. Replies
    18
    Views
    502

    MinnKota Digital for LiPo???

    Are these able to charge LiPo batteries? From what I can tell they are supposed to be able to reading on their site. Thoughts?
  10. Replies
    9
    Views
    1,059

    I wanted to update this thread even though I'm...

    I wanted to update this thread even though I'm not the OP. The root cause ended up being a plug wire cap. I was informed that these are fairly common, not the wire itself but the orange cap. They...
  11. Replies
    1
    Views
    289

    24v 50 AH Batts

    How many hours of use are those of you using this setup getting?
  12. Replies
    2
    Views
    177

    Yes. Thanks.

    Yes. Thanks.
  13. Replies
    2
    Views
    177

    HPDI VST pump O ring part number

    Hey all, looking for the part number for the o ring on the outlet side of the VST pump. This fits into the housing and the outlet end slides into it and buts up against the collar. Model number VZ150...
  14. Replies
    9
    Views
    1,059

    I took my VST housing apart and found sediment...

    I took my VST housing apart and found sediment right below the screen filter. Put a new one in and replaced both low pressure pumps right away. My guess is this was my problem and it was blocking...
  15. Replies
    6
    Views
    692

    Best hubs without bearing buddies

    Hey all. I recently replaced my entire axle on my Triton. This new axle has larger spindles and larger castle nuts. Bearing buddies will not fit over the castle nut. I've gone through a couple hubs...
  16. Replies
    5
    Views
    550

    Agreed. Lucky to get there. My Lowe 170W with a...

    Agreed. Lucky to get there. My Lowe 170W with a 70hp would hit 35 on a good day. The extra 20hp is getting you into the 40's and that's all you're gonna see.
  17. Replies
    9
    Views
    1,059

    I'd like to see what the response are to you...

    I'd like to see what the response are to you issue. I have a similar issue. It ran like a top a week ago. On the way back to the launch and it would bog down over when applying throttle over 4,500...
  18. Replies
    7
    Views
    489

    My opinion is that a manual plate will not get...

    My opinion is that a manual plate will not get you better hole shot. This will raise the motor and set the weight further back which makes it harder to push the bow down. I've never had a plate on...
  19. Replies
    4
    Views
    359

    This is reason enough. Conditions change and this...

    This is reason enough. Conditions change and this allows you to deal with them. On the flip side of this, you then have the ability to run shallow and still get the forward thrust you want from...
  20. Replies
    12
    Views
    483

    I just got off the phone with a repair facility...

    I just got off the phone with a repair facility that regularly deals with hyd. steering, finally found one over an hour away. They have an air purging machine. He stated every one of the hyd....
  21. Replies
    12
    Views
    483

    Good info for sure. I just put this on my boat...

    Good info for sure. I just put this on my boat last fall. The ram rod was good. There's never any fluid under my helm or the ram seals. Also, you can't budge the motor back and forth like he can....
  22. Replies
    12
    Views
    483

    I got a sea star helm now. Same issue. I still...

    I got a sea star helm now. Same issue. I still have the Uflex cylinder but if that were bad I should be able to move the motor left and right by physically pushing it.
  23. Replies
    12
    Views
    483

    I did this, twice. I did the original full...

    I did this, twice. I did the original full system bleed with clear hoses and clamped the cylinder as you should. I also then had it taken to a marine shop and he bled it with the same result. I...
  24. Replies
    12
    Views
    483

    I also wanted to add that you cannot move the...

    I also wanted to add that you cannot move the motor at all by grabbing the motor and pushing it to either side which tells me the cylinder should be fine.
  25. Replies
    12
    Views
    483

    Hydraulic Steering Issues

    Hey all, since I put in my hydraulic steering last fall there's always been slop in the wheel. Turning left to right there's a good 10 degrees of nothing before the motor moves. I spoke with Uflex...
Results 1 to 25 of 348
Page 1 of 14 1 2 3 4